1/6 scale Jetsprint boats and 30mm Jet drives

[TheShaughnessy]

Figures, I get my stuff stolen and these are finally ready. Gonna have to put in some OT.

[mickieb49]

Figures, I get my stuff stolen and these are finally ready. Gonna have to put in some OT.

I am thinking on selling the first few on a discounted rate , providing i get some Youtube footage of them.
Nearly got the smaller hull mold done, these will be Fiberglass, 450mm long. When i get the first one out of the mold i wil post some pictures.
Thanks for the feedback guy's, it is most appreciated.
Regards Mick

[Fella1340]

Looking forward seeing these available!

[mickieb49]

Hello all, I should have the jet units available in about 2 weeks, I should have all the injection molded parts on around the 21st, and the impellers around the following week. Will test one first, but all should be OK to sell some the week after , around 28th- 05th.
I am also going to put a few of these up for Christmas gifts.
Nearly finished the smaller hull mold, got a little wet sanding then polish before I can sell them, but hoping to have a few glass hull done before I release the jet unit.
Take care guys

[flraptor07]

How do you think these would work in a 36" or so cat hull twin setup? Might be fun

[mickieb49]

How do you think these would work in a 36" or so cat hull twin setup? Might be fun

Hi not too sure, I think it has been done before, went OK, as long as there is a 45_50mm flat section for the unit to mount to, it should go well.
Regards mick

[srislash]

Keep up the good work Mickie.

Waiting for outcome

[daveives]

Please put me on the list for one.
Thanks
Dave Ives

[mickieb49]

Will do ,
Just received 4 big boxes of injection molded parts, all up just a shade over 7000 separate parts.
Also finished the small jetboat mold, am hoping to be pulling the first hull out in the coming days. I will document the whole build here as I do it, I will also be making a instruction sheet to put these units and hulls together.
You will also see in the pictures of the building amount of parts I am accumulating ready for the release, hopefully in the next week or so as the impellers should be finished by the 21st November, and posted to me sometime next week, the boxes for the jet units should be in my hot hands next week too, also should be getting close to having some video footage about the same period.
Providing I get the new router bits this week I should be CNCing out the plug for the bigger jetsprint hulls this weekend???
Warm regards all, and thankyou so much for not getting too bored with me trying to get it all together.
20131119_194252.jpg20131119_194257.jpg20131119_194337.jpg20131119_200812.jpg20131119_200825.jpg

[mickieb49]

Here is the first small hull out of the mold, still have to retweek the cowl mold, but have started to put the jet unit into the hull, I am aiming to get most of it done so when I get the impellers, I can put one straight in and give it a run.
jets.jpgjetsp.jpgjetspr.jpgjetsprin.jpg

[srislash]

Looking good Mickie, I applaud your efforts on this

[rickwess]

Very interested in seeing this come together.

[mickieb49]

Hello all,
Well the router bit turned up, just had a go at machining out the lower half, apart from the fact that the spindle collided in the back and pushed the blank forward, I had to realign the blank , obviously it was not exact as there is a few places where it machined too much out. No big problem, I have filled these parts in and a quick sand , she will be ready to mold.
Take care hull front.jpghull lower fini.jpghull lowerrough.jpghull.jpg

[Tech Head]

Looks like your living the dream Mickie, everything looks under control.

I would happily sit and assemble those pumps, recon I could do it in my asleep after a week or two....

Are you going to package a complete RTR boat in a retail box? What's the total length including the pump?

[mickieb49]

Looks like your living the dream Mickie, everything looks under control.

I would happily sit and assemble those pumps, recon I could do it in my asleep after a week or two....

Are you going to package a complete RTR boat in a retail box? What's the total length including the pump?

Hi mate, I will be selling either the jet units desperately or a hull/jet unit kit ( complete with alloy roll cage, dummy drivers, SS pump guard). Both ways will be in a retail box complete with instructions.
The hull you see at the moment is only available until I get the new 610mm jet sprint up and going, this hull will be Vacuum for men ABS , I will eventually do a fiberglass version but like the NQD boat, I am expecting that this boat will mostly be used in rivers and creeks, generally where there is rocks.... I have been working on sticker kits too, but I need a few more funds before I can make hose available.
Thanks for your interest.
Regards mick