Your MG that started off as a hull

[macdon]

Don't do it man.The 180-POOF

Thats right! I dunno what I was thinking - it should've been 4s. I was also considering a 1500kv motor which would work on 6s. Got both mixed up I guess.

[srislash]

Ah yeah! Yeah! Sorry! It's meant for single drive!

I found this one brother but my concern is that, it has a 1/4 shaft.
[ATTACH=CONFIG]69470[/ATTACH] [ATTACH=CONFIG]69471[/ATTACH]

I am so down with that hydraulic setup Stephan!How much can you get that for or where.

[srislash]

Thats right! I dunno what I was thinking - it should've been 4s. I was also considering a 1500kv motor which would work on 6s. Got both mixed up I guess.

I have heard of guys running the 1515 on 6s but I don't know about amps.I was hitting 185 amps with a M445,not sure with the X645 that is on it now.
Did I see that one of you's got a 1717?You could run a 1/4 shaft that is cut down to 3/16.
rudder 001.jpg
There is my rudder.That is probably the same as the one you found and like you say, for twins.
I think I'm getting another 1515 localy

[macdon]

I am so down with that hydraulic setup Stephan!How much can you get that for or where.

Contact Johnny Cheung of HOR racing in HK.

Here you go, its the third from the top:

http://www.horracing.com/index.php?cPath=35&osCsid=onh6tj69ffnjsgjom4s3sngel6

[macdon]

I have heard of guys running the 1515 on 6s but I don't know about amps.I was hitting 185 amps with a M445,not sure with the X645 that is on it now.
Did I see that one of you's got a 1717?You could run a 1/4 shaft that is cut down to 3/16.
[ATTACH=CONFIG]69474[/ATTACH]
There is my rudder.That is probably the same as the one you found and like you say, for twins.
I think I'm getting another 1515 localy

That rudder pic of yours looks very similar to the one im considering in ebay:

http://www.ebay.com/itm/Aluminum-Rud...#ht_500wt_1198

[srislash]

Thats it exactly,mm what'd I pay?$45 seems to ring a bell.Kintec I believe.

[macdon]

Thats it exactly,mm what'd I pay?$45 seems to ring a bell.Kintec I believe.

Seems to be a good deal too - $20 for the rudder and $5 for shipping.
How's yours working for you?

[lenny]

Hi,
On my 37" Daytona I have a strut and rudder close to this, http://forums.offshoreelectrics.com/...8&d=1288497917
Mine is an old fine design strut and rudder with out the 1"extended from transom.
I think it help alot in better turning on that hull. http://www.youtube.com/watch?v=lnnhu..._order&list=UL
My Rio mod, http://www.youtube.com/watch?v=DwMgw..._order&list=UL

LMK what you think.

[HYDROJERRY]

the inline rudder you shown i have on my Genesis and i took the same rudder setup and removed the strut and cut the bracket short and installed it on my twin,,,
boy its hard to keep up with you guys, i get off and then theres like 15 post to catchup on, woow!!!!hahaha, keep-um comin!!

[macdon]

Hi,
On my 37" Daytona I have a strut and rudder close to this, http://forums.offshoreelectrics.com/...8&d=1288497917
Mine is an old fine design strut and rudder with out the 1"extended from transom.
I think it help alot in better turning on that hull. http://www.youtube.com/watch?v=lnnhu..._order&list=UL
My Rio mod, http://www.youtube.com/watch?v=DwMgw..._order&list=UL

LMK what you think.

Thanks for sharing Lenny and your vid runs looks great!

I found something similar to that pic of your rudder from HOR Racing in HK. Here's the description:

http://www.horracing.com/product_info.php?products_id=334

It doesnt have any measurements, so I emailed Johnny Cheung. Havent gotten a reply yet. There's no pic in the page, however I think this would be it.

[macdon]

the inline rudder you shown i have on my Genesis and i took the same rudder setup and removed the strut and cut the bracket short and installed it on my twin,,,
boy its hard to keep up with you guys, i get off and then theres like 15 post to catchup on, woow!!!!hahaha, keep-um comin!!

I went to HK and checked out the pics of their Genesis and it's rudder looks like the inline rudder I got from R2hobbies for my MG. However, that rudder is only 115mm (4.5") long. I dunno if sellers of these inline rudders have possibly swapped the 115mm rudder to something longer and used it for the Genesis. Could you possibly measure the vertical length of your Genesis rudder, Jerry?

I saw alot of those inline rudders being sold in ebay & other websites and all are 115mm long. However, the rudder length in Jerry's pic above shows the rudder a bit longer. Maybe they've swapped it? ...............either that or my eyes are playing tricks on me! hahaha!

[macdon]

Okay, I think I got it (maybe) - the Genesis rudder and the common 115mm rudders may have the same brackets - but the rudder blades are different. Going over HK Genesis pics and Jerry's pics above - the water inlet for the rudder is further down near the edge, while the common 115mm rudders have the inlets a bit higher. This concludes a swap ............ or I just need sleep! hahahaha!

[jasoncyclone]

Do you ever sleep Macdon???

[srislash]

Do you ever sleep Macdon???

That's what I was beginning to think.We were on here last night my time,they had posts all night and still now.I see a crash coming on.
Oh,hey,Jason.I picked up another 1515 today with MM ESC for $160.Think it'll power this 37" Cat

And Mac,I think the 150 rudder that I have is gonna be a bit much.I may be cutting her down.

[tagasagwan]

A few minutes of power nap and whole day tinkering with his rc boats is what he do! hehehe! Me, I sleep like a baby! hahaha!