Your MG that started off as a hull

[srislash]

what's the technique in removing the wood? do you heat it up and lift?

I use a dremal,exacto knife and pliers to remove it.

I got this picture Jason



I made a space for the zip tie to go under the front bulkhead and under the wood and up through the square hole by the top right of the decal.One of the ears on the ESC should slide in the slot in the bulkhead making it a nice comfy ride for the ESC.
Did you get the o ring on the motor OK?

[skyman]

I use a dremal,exacto knife and pliers to remove it.

I got this picture Jason



I made a space for the zip tie to go under the front bulkhead and under the wood and up through the square hole by the top right of the decal.One of the ears on the ESC should slide in the slot in the bulkhead making it a nice comfy ride for the ESC.
Did you get the o ring on the motor OK?

shawn, are you asking me about the O ring? i'm just going to get the one u recommended

[srislash]

shawn, are you asking me about the O ring? i'm just going to get the one u recommended

That post was directed to Jason and the start of page 74

[jasoncyclone]

Yep I got the o ring.. I still can get over the fact that I have my own logo!!! I love it!!

[skyman]

That post was directed to Jason and the start of page 74

shawn, can u explain to me the process of how you removed the wood for the battery trays (e.g. in the Miss Behavin) and put it back?

[macdon]

Yep I got the o ring.. I still can get over the fact that I have my own logo!!! I love it!!

Shawn is certainly our guru here in OSE!

[tagasagwan]

Shawn is certainly our guru here in OSE!

Shawn's Da Man!

Hope i can make my Skunkworks gen 2 cat as clean as how Shawn did Jason's MG

[srislash]

Shawn is certainly our guru here in OSE!

Here we go again

[srislash]

shawn, can u explain to me the process of how you removed the wood for the battery trays (e.g. in the Miss Behavin) and put it back?

ED,I did not remove all the wood and replace it.I only removed the front piece. I just scored along the edge of the bulkhead with a good sharp Exacto.On the front piece of wood that holds the stock motor mount,there are tabs that lock into the rails that go length wise on the tunnel floor.Just score it repeatedly and carefully,so as to not gouge the hull.All this wood merely has a light epoxy coat that bonds the pieces of wood together.Does this make sense?I can be on here to answer questions tonight.
I HAVE TAKEN THE WEEKEND OFF

Oh yeah, I have CF plate to make for someone.

[tagasagwan]

Here we go again

Admit it Shawn! You did great on your projects! Only few people has those talent! It's like Mardon creating something from cardboard and turn them to Fiberglass, Like Jason and Master Oca doing gas boats. Like me doing nothing! JUST CHILLIN!!!

[tagasagwan]

Oh yeah, I have CF plate to make for someone.

Nice!!!

[srislash]

Admit it Shawn! You did great on your projects! Only few people has those talent! It's like Mardon creating something from cardboard and turn them to Fiberglass, Like Jason and Master Oca doing gas boats. Like me doing nothing! JUST CHILLIN!!!

Thank's for all the great comments.It does make me feel good.

[tagasagwan]

You should! Plus you have the whole weekend off! Lucky you! hehehe!

[srislash]

And the Fightercat has cobwebs on it.I better blow those off eh.

[tagasagwan]

yeah better run your boats this weekend! My gasser is out of commission! The only way I can run it is, if i can borrow one of Mac's giant servos! hehehe!