I had a chance to test it today and it ran well. The prop I used is a plastic Graupner 2317.45 (1.4 pitch, 45mm diameter). The water was rough but the Stealthwake runs much "dryer" now. Before, most of the hull was planted in the water. It's trimmed out much more now. It's probably going to take some tuning to get it running where I want it. Right now it's a little bow high and can trip and stuff in bigger waves. Still, this didn't happen except for a couple times and it ran really well otherwise. Stock the boat ran 19.7mph on 2S the one time that I GPSed it. Today it ran 26.3mph on 2S and 28.3mph on 3S. The water was to rough to do full throttle runs on 3S in it's current state and before I switched to 3S, the plastic prop got chipped on floating debris. Anyway, I've been having fun building this thing.
Stealthwake1 (Medium).jpg IMG_0140 (Medium).JPG IMG_0221 (Medium).JPG IMG_0222 (Medium).JPG
-
The motor is the 1800kv Dynamite out of my Impulse 31 V2. It's the right size for the mount and I decided to try it before buying anything else. The Seaking 180a ESC is overkill too but I had it sitting around and the bullets were already set up for the motor and my batteries. The side of the ESC says 3S-6S but it works just fine on 2S. The stock ESC bolts onto it's mount so I cut off the threaded nipples and then the ESC fit great. I blocked off the hull water intake with a bolt and tubing for now.
IMG_0209 (Medium).JPG IMG_0211 (Medium).JPG IMG_0213 (Medium).JPG IMG_0216 (Medium).JPG IMG_0212 (Medium).JPGLeave a comment:
-
The stock drive is a straight stuffing tube with a 3mm threaded drive shaft. The stuffing tube has a outer diameter close to 9/32 but has reducing bushings in the ends so that the 3mm drive shaft fits tightly. I decided to remove the stuffing tube and install 9/32 tubing so that I could use a liner and .187" flex shaft. The strength is overkill but this way I didn't have to do anything crazy to be able to use 3/16" props. The stuffing tube and flex let the drive shaft be parallel with the bottom of the boat instead of the downward angle of the straight shaft. The install went very smoothly except that the 9/32 tubing was a tight fit. I figured that this would be a good thing but it ended up putting a 1/2" long split in the keel right under the stuffing tube entry. I sealed it with CA glue and I'll keep an eye on it for now. It looks worse than it is I think. If you try this, make sure the stuffing tube slides in easily. Don't stress the plastic hull to much.
IMG_0150 (Medium).JPG IMG_0158 (Medium).JPG IMG_0208 (Medium).JPG IMG_0220 (Medium).JPG IMG_0210 (Medium).JPGLeave a comment:
-
The stock rudder and bracket are plastic and there's quite a bit of play in the mount and flex in the rudder. I also wanted to get a rudder with a water intake in it just in case I decide to eliminate the bottom mounted water pickup. I ordered a rudder for a Blackjack 24/Shockwave 26 and it worked out really well. It's the right size and two of the holes in the transom line up almost perfectly. I did have to drill two more holes for the new rudder. The aluminum Blackjack rudder is mounted a little deeper than the stock rudder to hopefully make the boat a little more stable at faster speeds. The steering arm is on the correct side of the rudder but I had to bend the steering rod some in order to hook it up but the stock length worked fine.
IMG_0175 (Medium).JPG IMG_0177 (Medium).JPG IMG_0180 (Medium).JPG IMG_0185 (Medium).JPG IMG_0188 (Medium).JPGLeave a comment:
-
So I've been messing around with this Stealthwake a lot recently. I bought this boat with the intention of building it with a brushless motor setup that was hopefully capable of running 3S. So don't take these modifications as shortcomings of the stock boat. It really is a blast right out of the box. The Stealthwake comes with a 550 size brushed motor and air cooled esc. They come out easily. The water outlet on the stock boat is just the end of the cooling tubing glued into the side of the hull so I swapped that for a Aeromarine stainless outlet for 7/32 tubing.
IMG_0156 (Medium).JPG IMG_0195 (Medium).JPG IMG_0196 (Medium).JPGLeave a comment:
-
I agree Rafael. Very fun boat! I actually do have a flex cable setup ordered and a 1800kv motor to test in it. Thanks for the tips. That is very helpful. I really don't want to hurt the rough water fun of the boat. I wonder how a slightly scaled up version would run?
Leave a comment:
-
I didn't develop this one but I sure enjoyed testing it. It's a very fun boat.
Some personal tips as a boat geek, and not as a Pro Boat Product Developer, if you mod it, definitely add a flex cable and get the prop level. Max motor is 2000kv on 3s. I used our Dynamite 30A ESC, thogh a 60 will give more prop range. More power than that from motor/battery combo and the boat becomes very erratic because of it's narrow beam, especially if you still plan to run in rough water. But boy is it fun in rough water!!
Modding of course is done at your own risk
Leave a comment:
-
Bought a ProBoat Stealthwake to play with
I've been looking at this funky deep-v for a while now and finally pulled the trigger on it. I've been running my Voracity several times a week lately but once in a while the water is to rough for speed passes. When the water is that rough, it's a blast in the Stealthwake. I run it on 2S Lipo packs through a EC3 to 5.5 bullet adapter I built. The stock motor and electronics seem to work well together but I'm working on a brushless setup for it. Maybe run 3S in it. The stock motor has a cooling coil around it but the ESC is not water cooled. The water pickup is in the bottom of the boat so they can use a solid rudder to save money (I assume). Anyway, here are a few pictures. I'll try to add some more as I mod this thing.
IMG_0123 (Medium).JPG IMG_0124 (Medium).JPG IMG_0125 (Medium).JPG IMG_0148 (Medium).JPG IMG_0152 (Medium).JPGLast edited by arrover; 03-27-2016, 09:30 PM.
Leave a comment: