32" Mono Build

[sailr]

...isn't load on the rear motor bearing...

That's why I always use a thrust bearing at the motor! The load goes on the case or mount rather than the bearings.

thats one good thing about them you wont loose a prop if the coupler comes loose, but usally with this setup you run a small teflon washer between the dog and strut so the push from the prop is placed at the strut not the motor wich can change the characteristics of how the boat runs, this also means there isnt load on the rear motor bearing either.

[sailr]

I don't want to jump into Nate's deal, but if he wants to pass on the mount, I might be interested. What is the price? Is it nailed in stone for the 1527 or could it be used for a 1515 also?

Nate if you still eventually want your mount here is the 4in / 5in combo 1527 mount you requested . If not someone else will eventually nab it so no biggy there either

[Punisher 67]

Price is $75.00 James . I have over 5 hours into moding this one

I have frame connectors that will enable one to use it on the 1515 also that can be thrown in , just makes the mount shorter , you won't be able to use the top plate if you do

[sailr]

GREAT price! What would you charge to make a top plate for the 1515? I would like the mount, extra frame connectors, and additional top mount.

[sailr]

one more question. You say it is 4in/5in combo. I don't see how the width is adjustable. What am I missing? As it is, what is the width?

[ozzie-crawl]

looks like the sides that bolt to the stingers is removable

[sailr]

Aha, I see it now. thanks.

[calcagno45]

Peter: Thats a beautiful mount! I can see you're really enjoying that mill!

[Punisher 67]

Peter: I can see you're really enjoying that mill!

Cory about as much as the two hotties in your avatar are enjoying sucking face.......................

Jim I will have to rewrite the 1527 top piece and adjust the length and machine one , would $90.00 shipped be asking to much for every thing

[bustitup]

Peter
I'm just waiting for my 42" sprintcat to get here and will be ordering that 2215/2y mount and top plate from you...I dont know the spread of the rails or I would order it now

[calcagno45]

Cory about as much as the two hotties in your avatar are enjoying sucking face.......................

I just about rolled on the floor laughing!!!

[Punisher 67]

Nick that would have a flat floor correct , lets wait and see . I have to design some mounts with a flat bottom for cats anyways . I will try to make them as stylish as the mono mounts . 4inch and 5inch

mount and top plate would look like much this but with a flat botton

http://forums.offshoreelectrics.com/...5&d=1245700810

[bustitup]

Nick that would have a flat floor correct , lets wait and see . I have to design some mounts with a flat bottom for cats anyways . I will try to make them as stylish as the mono mounts . 4inch and 5inch

mount and top plate would look like much this but with a flat botton

http://forums.offshoreelectrics.com/...5&d=1245700810

no Peter....it has a small v in the bottom that looks like that mount would fit right in there

my hull is the aeromarine 42" sprint cat

[nate]

Nate if you still eventually want your mount here is the 4in / 5in combo 1527 mount you requested . If not someone else will eventually nab it so no biggy there either

Awsome Job Peter, That things a beast.

I tell ya what, my build is Off for use of this mount for a few months, but will eventually need it anyways, so If anyone is interested in this badass mount go for it.... if it dosnt sell for asking price in a day or so ill go ahead and pay ya for your nice work Peter. Thanks man.

[Punisher 67]

Nate I think Sailr is interested in it , I can always make you another later when you need it

Nick the mount above is a large and the only one big enough to fit a Neu 22XX . these mount are 3/8 thick and take 6+ hours from start to finish and I charge $125.00 shipped for them . I can make the same mount in a 1/4 inch and probably shave off $25.00 to make things cheaper . I'm sorry about the cost but they take a huge time commitment to make one