A lot of pain today Larry. Catch up with you tomorrow or something.
-
Nortavlag Bulc -
Bottom all done and sanded.
Now to start on the top sticks.
LarryPast NAMBA- P Mono -1 Mile Race Record holder
Past NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & WetComment
-
More clamps -Top deck sticks.
LarryPast NAMBA- P Mono -1 Mile Race Record holder
Past NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & WetComment
-
Decking bent and glued.
LarryPast NAMBA- P Mono -1 Mile Race Record holder
Past NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & WetComment
-
You suck Larry... lol, j.k... I like the file trick, cool! Should'a showed me the bending part
Maybe I'll get the turn fin done tonight so I can deck mine tomorrow. Nortavlag Bulc Comment
-
Ray
I put one side along the table, with weights along an edge about 1/2" into the sponson decking.
Then I added some clamps for weight along the outer edge to help bend the wood.
Then I went at it with the heat gun.
After that one cooled, I did the other one for the other side.
LarryLast edited by TRUCKPULL; 05-18-2023, 12:10 AM.Past NAMBA- P Mono -1 Mile Race Record holder
Past NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & WetComment
-
Thanks. I'll give it a try. I don't like bending wood with hot water when it's a large skin like this. Too easy to mess up the top layer finish. Nortavlag Bulc Comment
-
RAY
I remember about 10 years ago when I was building one of my N2 Wip's.
I made one side, as I was in the middle of the other side, I realized that I was making two right sides.
Had to cut a new piece, Although I now had a right side for my next one.
Please be careful, and don't do this.
LarryPast NAMBA- P Mono -1 Mile Race Record holder
Past NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & WetComment
-
Thanks for the heads up! Much appreciated.
Maybe I'll cut some out of 1/32" ply, lol.. jk.. Nortavlag Bulc Comment
-
Top deck all glued down and sanded.
Front nose piece cut to fit, ready for glue.
LarryPast NAMBA- P Mono -1 Mile Race Record holder
Past NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & WetComment
-
I have been working on hardware, drive shaft, and electric, ECT.
Now I have to make one of my race cowls for it.
LarryPast NAMBA- P Mono -1 Mile Race Record holder
Past NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & WetComment
-
Looking good sir! Servo is in weird but I get it. I'm finally getting the turn fin sorted out. I had to buy new threaded rod since the kind that is only threaded on each end just would not work.
Do you use wood screws to put in the servo or nuts and bolts? Nortavlag Bulc Comment
-
Wood screws.
LarryPast NAMBA- P Mono -1 Mile Race Record holder
Past NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & WetComment
-
what are all these black pearl hulls everyone makes threads about? I searched for them and nothing came up.Comment
-
Look at post #34Originally posted by Bande1 View Post
This is the gentleman that makes the kits.
LarryPast NAMBA- P Mono -1 Mile Race Record holder
Past NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & WetComment
Comment