HPR 010 Mono: Very Slow Build

[boredom.is.me]

Update:
- The hull is in customs.
- I'll hopefully be getting the rudder from WD200-ModellBau, which is the original maker for HPR's rudders. It's less than half the cost direct, which I don't quite understand the markup. I wasn't at all trying to be a cheap skape as this was an accidental discovery but damn... It will not come with the hydraulics, but I don't think they would fit properly even with a mild standoff on the rudder. Unfortunately, they are closed till the 8/21.
- I've decided to skip out on trying to make my own cf sheets. I've shifted ideas around to bring everything down to only two thicknesses.
- The aluminum for the motor and accessory mounts is on the way.
- I may go with the Swordfish Pro 220 ESC's over the T180. They would give more headroom, are lighter, and are easier and potentially cleaner to mount.

[boredom.is.me]

One thing has been driving me absolutely crazy. That is the spacing between my prop centers. The closer the prop centers are to eachother, the lower I can seat them. Without incorporating a pair of S bends, the closest I can comfortably get the motors together in the double mount is 52mm. That leaves enough for up to 50mm jackets with an extra 2mm of wiggle.

The largest prop I could ever fathom running would be a 50mm. That's damn near touching with that kind of separation. I'll probably just stick with a pair of 45mm props.

What effect does this have on the rudder?

[boredom.is.me]

Awesome thanks. I got an estimate of about 2 weeks until they are back in stock.

Hopefully, I can start working on samples for the carbon sheets today. I'll start with 1.5-2mm for the ESCs and other accesories.

[iridebikes247]

I would go with 1650, definitely. Props you should be good with 447s, I ran 447s in a twin cat with 1600kv leopards 4082s, sk180s and it was a 70 mph setup. I think this will be fast enough if you're looking for a conservative setup.

[boredom.is.me]

After seeing a few recent "events", I'll just go ahead and stick with 6s. Staying with SSS, they have the 4092 available in 1400kv and 1650kv. I do want to keep it pretty conservative. Any suggestions/advice would be greatly appreciated.

[boredom.is.me]

It's shipping out next week!

[boredom.is.me]

I sent the payment yesterday, but I'm stilling waiting to hear back from Hans about a previous message.

[boredom.is.me]

Here is the battery sled, stuffing support, and trailer. Again, any advice on materials would be greatly appreciated.

I'll probably end up using three, possibly four, different material thicknesses so I have decided to try my hand at making my own sheets. Ordering a million different sizes is a bit much.

BatterySled_1.jpg TwinMount_3.jpg Trailer45_1.jpg

Please, if anyone feels my choice of whatever is a bad idea, please let me know.

[boredom.is.me]

Hey everyone,

This will be a very slow build. In fact, I don't even have the boat. I'm in communication with Hans at the moment about it. I won't be able to order till the 21st since I'm out of the country with no way to make a bank deposit...but moving on. I'm starting this early to get ideas, suggestions, and opinions (both positive and negative).

HPR 010 Mono:
- Carbon Kevlar Hybrid

Electronics:
- SSS 4082 2000kv (x2)
- Turnigy Marine 180A (x2)
- Turnigy 1259TG 16kg
- Turnigy Heavy Duty 5000mAh 4S 60C (x2 in Parallel)

Hardware:
- HPR Twin Drive Set
- Kintec 6 Inch Short Base Cat Rudder (possible)
- Custom Twin Motor Mount
- Custom Carbon/Aluminum Battery, Servo, Rx, and ESC Trays
- Push/Pull Linkages
- Stainless and Anodized Aluminum bolts/nuts/washers
- Castle 6.5mm Bullet Connectors

Extras:
- Running Lights
- Custom Trailer




Why I chose the SSS...
This isn't exactly a budget hull, but I really am not interested in having a saw boat or anything like that. I just want to have fun. With that said, Neu and Lehners are definitely not options. My choice for motors were Leopard, TP, and SSS. I decided on the SSS due to all the claims of how efficient and cool they run compared to the other two. In fact, Leopard is the overall worst of the three what all the reading I have done. The plus is that the SSS is actually the least expensive option. The 2000kv is also safe on 6s which would be fun for a quick sprint.

Motor Mount Advice...
The face plate and rear support will be made of 1/4" aluminum. I'll use M4 bolts to attach it to the side plates. I'm kind of lost on what to use for the side plates. I have three options. I can use aluminum, carbon, or carbon/kevlar. Aluminum could bend, takes a while to machine, and is the heaviest as I would more than likely use the same 1/4" stock. It is the cheapest. Carbon fiber could definitely handle it, but how thick is necessary? It cuts relatively easily. I was thinking about 3/16". It would be about 10x as much as the aluminum in cost. Carbon/Kevlar is stupid expensive so I would have to make it myself. I am uncertain of how it cuts. The strength is also a bit of a concern as making it wouldn't exactly be a perfected science like the manufacturers. I would use the glass panel method and build it up to approximately 3/16". It would match the hull as I can get the same weave cloth, but at the same time, that may not be "nice" or "cool". The side plates pictured below are 3/16". It is also 65mm spacing between motor centers which is subject to change.

TwinMount_1.jpg TwinMount_2.jpg


Kev

__________________________________________________ __________________________________________________ ______________
Edit - Current Setup:

Electronics:
- Suppo/FC 3730 1580kv Outunner x2
- T180 ESC x2
- Turnigy 1259TG 16kg

Hardware:
- WD200 Ruder M (HPR 135) Rudder
- HPR Twin Drives
- Custom Carbon Servo Mount
- Custom Carbon Battery Sled
- Custom Carbon/Aluminum Motor Mount