FDM 32 V-Hull Build - Need Build Advice

[Tamelesstgr]

Looking to get some holes filled that I will not be using. Should get the flood tube set this week as well. Servos I got from the Swap and Shop are a little taller than the stocker I mocked everything up with. I'll have to make another set of servo uprights, but that's ok.

20160320_070953.jpg

20160320_070957.jpg

20160320_072702.jpg

20160320_072717.jpg

[Tamelesstgr]

Got the holes filled and the flood tube epoxied in place, up next is setting the motor mount rails in place.

20160405_213307.jpg

20160405_213313.jpg

20160405_213344.jpg

[Tamelesstgr]

Finally took the plunge and epoxied the motor rails into the hull, feels really solid

20160408_070036.jpg

20160408_070049.jpg

20160408_070056.jpg

[Tamelesstgr]

Taking the paint off this hull is
Wet sanding is taking forever, my fingers might be nubs soon
I've tried oven cleaner, it helps only a little, paint is very thick

20160420_224257.jpg 20160420_224252.jpg 20160420_224302.jpg

[Tamelesstgr]

Slow Progress, decided to spend some time on the modified hatch covers. Glued these up and cut an opening the same size on the bottom side of the hatch. Epoxied them to the hatch, and I will probably coat the entire underside of the balsa to make sure it's water tight. I will also lay some light fiberglass cloth on the vertical part of the engine cover and overlap the ABS hatch just to make sure there is no chance for separation during a flip or flexing of the hatch. Pretty happy with how they are turning out.

20160428_222902.jpg

20160428_223644.jpg

20160429_103150.jpg

[Tamelesstgr]

Like the look over the previous engine covers

20150804_222136.jpg

20160429_103137.jpg

20160429_103143.jpg

20160429_103119.jpg

[T.S.Davis]

If you check with Fine he may have the scale looking drivers for that kicking around.

[Tamelesstgr]

I've got them, debating whether or not I should try and find a little more scale looking drivers, probably won't have them in the cockpit for power runs.

PART_1434374017201_20150611_105302.jpg

[Tamelesstgr]

Finally got a chance to jump back on the hatches since I will certainly need my cover if I intend to run soon. Worked out pretty well I think. Opened up the holes to match the wooden hatches and epoxied them to the ABS hatch. Then I added 2 layers of some thinner fiberglass that draped over the wood and ABS to kind of tape them in place with some lighter finishing epoxy. Now I have added 2 coats of the finish epoxy to the raw wood. This finish epoxy sands so much nicer than the thicker stuff I use for mounting motor mounts etc.

I wonder how many coats are needed before final sanding for paint? I want to do a leak test and then fill the underneath part of the wooden hatches with expanding foam or maybe stryafoam to be sure the hatch doesn't sink.

Thoughts?

20160510_221218.jpg

20160510_221213.jpg

[Tamelesstgr]

Here is what I ended up with for my steering. Still trying to decide if I should add the left side steering rod, or just leave the right side alone? It's a 4-40 rod. I'll have to disconnect in order to be able to move the rudder out of the way to pull the flex after each run. Kind of a pain, but I may address the offset rudder later.

20160516_214205.jpg

20160516_214212.jpg

20160516_214226.jpg

[Tamelesstgr]

First side of parallel battery harness with spark arrestor. Soldering is not my favorite thing, need more practice, but joints were prepped with flux and are solid.

20160519_230616.jpg

20160516_220601.jpg

20160516_221707.jpg

[Tamelesstgr]

Any thoughts on what I can do to secure my 6s battery packs? I have seen folks epoxy the battery strap right to the hull. I don't think a traditional tray will fit in the space I have. I could make 2 fiberglass pieces the straps could loop around and epoxy those to the hull.

20160428_232936.jpg

20160428_232223.jpg

[Tamelesstgr]

Some progress being made, epoxied in the steering linkage tubes and positioning of the dual cooling lines.

20160523_224938.jpg

20160523_230154.jpg

20160523_230213.jpg

[Tamelesstgr]

With my EagleTree eLogger I can log three separate temp probes. Unfortunately there are not any air holes in the endcaps of my Leopard 4082 that would allow access for a temperature probe. I pulled off the end bell and located a spot to drill an access hole I can get the thermistor close to the windings. I used a backer to protect the windings from the drill bit. Also made double shure no shavings are inside the motor.

20160523_220331.jpg

20160523_220337.jpg

20160523_220438.jpg

20160523_220426.jpg

[Tamelesstgr]

Concept for Paint and Graphics

20160526_072128.jpg