swordfish plus with data logging

[Rumdog]

Id bet it's like the old CC controllers. You could do it, but need to solder a bus between the wires near the esc.

[drwayne]

The pair of battery inputs must be joined together.
The esc here have awg6 on both sides 1

[Brushless55]

Id bet it's like the old CC controllers. You could do it, but need to solder a bus between the wires near the esc.

The pair of battery inputs must be joined together.
The esc here have awg6 on both sides 1

can anyone post a picture of this for me?
thanks

[drwayne]

Will scan manual's wiring diag too as it has pretty colors for the technophobes amongst us...
meanwhile ..

300.JPG


here's the manual.

[Rumdog]

Why did they have to make it so awkward. Not a fan. I'd prefer the new 240. Simple single leads, plus still fully waterproof.(supposedly)

[Chrisg81983]

I agree with that but are the new 240's waterproof or water-resistant

[Rumdog]

Says incased in rubber, making it very water resistant. A good word to use to cover their behinds too.

[Prop-a-Gator]

So what happened to the std SF240HVs here at OSE? Are we going to see them on clearance, or were they actually sold out? I don't need the data logging, but do need a new ESC. Not to get too far off topic, has anyone tried the new Etti 220A HV? I noticed it had 2 pairs of battery leads and 2 sets of motor leads.

[Chrisg81983]

The etti 220 Hv is an amazing esc I will take it over a swordy any day but that's just my op I have tried almost every Hv esc out there and they are one of the top on my list

[Steven Vaccaro]

Ok so, if i buy one for my big Leo, why does it have two sets of wires?

to carry more current.

[Rumdog]

Do you still have to program via Tx with the 220 hv?
Thats a deal breaker for me. I mean, I can do it, but there are just so many better ways now.

[Chrisg81983]

Rum I always program my etti's with radio I think the ettis are the easiest to program via tx I can probably program it quicker or about the same with my tx over my swordy with the programing box

[Brushless55]

Will scan manual's wiring diag too as it has pretty colors for the technophobes amongst us...
meanwhile ..

[ATTACH=CONFIG]79989[/ATTACH]


here's the manual.

Ok, so to me it looks like I can use my 5.5mm bullets on all 4 battery connectors and use a jumper wire ( red to red / black to black )
and have my 8s2p pluged into the esc without any parallel connectors...

[drwayne]

Ok, so to me it looks like I can use my 5.5mm bullets on all 4 battery connectors and use a jumper wire ( red to red / black to black )
and have my 8s2p pluged into the esc without any parallel connectors...

The 'jumper' wire needs to be decent 8AWg same as the esc.. I trimmed 50mm off one lead.. and soldered that ne direct to it's mate. .. see pic above inside large genesis cat for eg.
I ran 12S1P50C5800 to each esc on maiden in above twin cat.. smooth output ..
I Hammered it !!! (before sending away to new owner !)
I know he will be happy with their performance.
W

[RIPFENCE]

So if i want to 2p i solder the 2 leads together and then use a "y" connector on each lead? I cannot use a single battery per lead and get 2p correct? Just want to understand this correctly...

Brushless are you doing this without soldering the leads together? I totally suck with wiring and i am surprised i have gotten this far with some big voltage setups without killing myself lol