W.T.B. hull and hardware34-36"

[montymike]

Wanted to buy hull and hardware like a cheetah or areomarine avenger, team believer sprint cat in good shape. With good
Offset rudder setup.

[meangenesracing]

aeromarine avengae "36

i got this was setup for twin neu motors but i do have a aeromarine strut and rudder

[montymike]

sorry I guess I should have been specific was looking for one that was set up for a 1 motor with all hardware
That all had to do as add electronics thanks for the look

[darryl whitman]

rivercat 025.jpgrivercat 026.jpgrivercat 028.jpgrivercat 029.jpgI have a rivercat with hardware , if u want I can place pic's , the sponsons r blueprinted by Travis, the boat has never been ran yet, I have too many projects on hand , so I may sell,

[darryl whitman]

here's morerivercat 034.jpg

[darryl whitman]

an morerivercat 031.jpgrivercat 031.jpgas u see CF inlay, servo an
servo mount, drive flexshaft , motor mount, the fab work is done, u ad motor , esc, radio, prop.

[montymike]

Yes more pics please, what motor set up for? What servo?
Looks like the fg. Version of the fighter cat ri ver cat. With the ofset kit fightercat hardware yes...

[darryl whitman]

A decent motor for it on 4s is the 1515 castle, 2200kv. That's actually what that boat is setup for. I'd run the revolectrix packs in it. You could do two 2s packs in series for 4s and have 5500mah of capacity and light weight or you could do two 4s packs in parallel for 11,000mah of capacity. I'd run a seaking 180 with a nice cap bank. I'd start off with an x442 prop. You could end up with an x642. Make sure you detounge them. The rear mount I sent you fits a castle finned motor. If you want a smooth 40mm can motor you'd have to get a ring from kintec or ose if they sell them.

If you wanted a really fast 4s boat, do a neu 1521 2900kv on 4s. I'd do two 4s packs for sure with that. If you haven't tried revo packs, you need to. They are worth more than they cost. They are cheap too....check em out.

[kfxguy]

[ATTACH=CONFIG]124040[/ATTACH][ATTACH=CONFIG]124041[/ATTACH][ATTACH=CONFIG]124042[/ATTACH][ATTACH=CONFIG]124043[/ATTACH]I have a rivercat with hardware , if u want I can place pic's , the sponsons r blueprinted by Travis, the boat has never been ran yet, I have too many projects on hand , so I may sell,

Actually that boat was setup and blue printed by chili. That's not fighter cat hardware. It's some billet heavy duty hardware. Very nice and strong. The hull is a fiberglass rivercat which has been reinforced very well.

[kfxguy]

A decent motor for it on 4s is the 1515 castle, 2200kv. That's actually what that boat is setup for. I'd run the revolectrix packs in it. You could do two 2s packs in series for 4s and have 5500mah of capacity and light weight or you could do two 4s packs in parallel for 11,000mah of capacity. I'd run a seaking 180 with a nice cap bank. I'd start off with an x442 prop. You could end up with an x642. Make sure you detounge them. The rear mount I sent you fits a castle finned motor. If you want a smooth 40mm can motor you'd have to get a ring from kintec or ose if they sell them.

If you wanted a really fast 4s boat, do a neu 1521 2900kv on 4s. I'd do two 4s packs for sure with that. If you haven't tried revo packs, you need to. They are worth more than they cost. They are cheap too....check em out.

Copy-paste? Lol

[kfxguy]

Hey darryl, how much you want for it back? I might get it back for my son if the other dude don't want it. I should have kept it. Lol

[montymike]

Yes price :

[montymike]

I have all parts listed above thanks...

[kfxguy]

I have all parts listed above thanks...

This is a 32" boat but it can run well. If you do get it and your not worried about saw runs and you want it to turn, I have the whole strut and offset rudder assy That you'll need brand new in package that I'll swap you. The rudder on this hardware is kinda short for anything but going straight.

[montymike]

Not worried aboat saw runs, just would put
A1515 2200 on 4s want to be able to turn.