WTB: FC carbon, daytona will look at all cats

[yachtsystems]

Looking at buying a zonda thought i would see whats here?

[h2o 1]

Whats ur budget? I have a VIRGIN Keith Bradley built CF Daytona twin drive with Hyperion outrunners.This boat was built just over a year ago and has been a display for me. I will advise,if ur new to FE, this is not the boat for you. It will require soldering of the esc and motor bullets and flat spots ground in the motor shafts. ESC is a new Fc Twin 240 with the field programmer.Again.everything is NEW,NEVER wet not even in a bath tub! If you would like to see it,i'll upload pics in this thread(its the boat in my avatar)

[h2o 1]

001.jpg002.jpg004.jpg005.jpg006.jpg
A few pics for you to see it. As you can see,options were left open for upgrades.If you dont like outrunners,all the plumbing is done for the inrunners. This is a truly sweet Daytona. Can take more pics of anything you want to see and i stand behind anything i will ever sell on this forum. Mark
Forgot to mention,this hull had the optional epoxy coating on the inside plus Keith did his magic with CF inlay over that.

[yachtsystems]

I like your Daytona. It does seem like a sweet setup. Very interested in talking with you on this.

[yachtsystems]

Would like to talk more with you on this Cat.

[h2o 1]

Todd, there's a build thread on this boat on the FC forum under Marks Daytona by Keith Bradley. Check it out. Thanks man,Mark

[yachtsystems]

I want it. inexperienced with the air cooling. What was your setup ideas on the boat?

[h2o 1]

When this boat was built my target speed was a modest 50mph.I wanted a scale looking boat with scale speeds. These motors are made by Scorpion for Hyperion.Outrunners made by Scorpion are top quality and can take more heat than any outrunners on the market without demagnetising and permanent power loss. I was going to run this 4s2p. Props are x442 Cnc heat treated. The only flaw on this boat is the corner of the windsheild sticker is slightly peeled due to my dusting and wiping once a week. Mark

[h2o 1]

008.jpg
Here the sticker i spoke of.

[h2o 1]

009.jpg010.jpg011.jpg012.jpg
Heres a few more Todd. Please note before you commit to this that this hull is exactly as i got it back from Keith other than a few added small pieces. Keith did not wrench any of this hardware super tight due to my instruction.My intentions was to eventually have this hull painted was the reason behind that. I was undecide on the battery trays or velcro so i never epoxied them down.You will have to tighten the hardware and seal this hull. Just so you know bro,no surprizes! Mark

[h2o 1]

This is what you will get Todd
FC Daytona hull with CF inlay by KBB
Custom CF motor mounts by KBB
Custom CF stuffing tube supports by KBB
Custom servo mount by KBB
Custom esc cover by KBB
KBB hatch bolt kit installed
2x Hyperion 3026 1900 kv outrunners
2x 110mm 3/16 stinger drives
2x Aeromarine flex cables,L&R
2x Aeromarine 3/16 collets
2 CR x442 aluminum props
2 long battery trays
Fightercat 240 Twin esc with programmer and all connectors for your batts and motors included
Kintec center mounted rudder 110mm
Everything in these pics is what you will get incase i forgot something. Hope this helps.

[yachtsystems]

This system was setup to run 4s as i understand? will it take 5s, 6s? Too much?

[h2o 1]

The motors are rated at 5s but i was only going to use 4s correct.I wouldn't personally run this on 5s,like i said top speed wasn't a factor.Play with it on 4s bro,im sure with testing and the right props it will surely be a pleaser.

[yachtsystems]

Payment sent. Shipping in notes. Please let me know when you receive it.

[h2o 1]

Got it Todd! Will ship in the morning and i'll pm you the tracking number.Ur gonna love this one bro,once its in your hands, you will see exactly why it was my flagship of shelf queens! Its that damn pretty!! Thanks again Todd,Mark