For Sale: KBB34 Mono w/ NEU 1521 and MGM 28026v3 Lite ARTR.

[complacent_one]

SOLD is my KBB34 Mono Almost Ready to Run

It is the same hull as kfxguy just sold.

This one was built much like that boat but utilizes mostly MTC Hardware off the back.

MTC Rudder
MTC Stinger
OSE Trim Tabs.

NEU 1521 2900KV 5mm Shaft. with kfxguy custom carbon wrapped water jacket
MGM Compro 28026v3 LITE with USB programmer and comm cable.
HiTec Waterproof Servo
Castle BEC
CC 6.5mm Green Batt connectors

When I first built this, I did take the time to blueprint the hull so it ran well and had minimal drag, for a mono.

I would like to get $800 plus shipping. I can include a new set of Revolectrix 4S 5000Mah Go Packs with CC 6.5mm Green connectors( have not been soldered on yet) for an additional $50.

It will come with a balanced, thinned,and sharpened Octura M447, m645, and m445 with that price. If you would like the pictured Andy Brown prepped 646-3 and kfxguy'd ABC 1615-17 then we can negotiate those in. I am willing to entertain a package deal with the other boat listed...I also have a Futaba 4PKSR with Life batt, 3 receivers, and aluminum case that can be leveraged into the deal.

[Leeandre]

Lovely . It’s a 4s boat obviously. What kind of speeds do you see with this set up.

[Leeandre]

I mostly run 6s set ups in my boats. Can a standard size 40 series motor fit in place of the Neu and would you be willing to sell hull and hardware less motor and esc ? Thank you.

[complacent_one]

Yes a 4060 or 4070 would fit. I would prefer to keep it as a package for now, but may consider breaking it up after this coming weekend. I have not run it in the current layout, but math put this one at around 22% slip or waste. So on 4s with the 646-3 , 80mph trimmed out. 3s for sporting around, 60 on a moderate prop.

[Leeandre]

Seriously interested , I have a 4070 and a 300 amp Flier.

[Jesse J]

Where in Texas, I’m looking at the package deal plus batts, I’m in West houston area, you?
Would like to do hand off and avoid shipping if possible.

I’ll take it if you can do $800 with batts and a hand off.

[complacent_one]

I am in Leander...NW Austin...with my diesel, it would be cheaper to ship...but I can likely do ground from office to Houston for around 20 bucks.

[Jesse J]

So, you could do $820 for package and revo packs shipped?
Hull, hardware, motor esc, servo and props.
I don’t need 6.5mm connectors, bare wires are fine.

[complacent_one]

Yes, I keep the 646-3 and ABC props...if you want those, $880 shipped.

[complacent_one]

I have a 4x8 sheet of 3/4" foam to keep things safe in transit.

[Jesse J]

Ok. $880.
Send PayPal and let’s roll.
Boat with electronics, two batts, three props plus two special props.

[complacent_one]

10-4...PM with paypal address, incoming.

[Jesse J]

PayPal sent.
Thanks john, I may call you tomorrow.
Jesse

[complacent_one]

Payment received. Please fire me a text first...
-John

[complacent_one]

Ok. $880.
Send PayPal and let’s roll.
Boat with electronics, two batts, three props plus two special props.

Packed and Shipped. PM with Tracking inbound and was also updated on Paypal. Should be there Monday.