Tp motors

[nmnorth]

Two TP Motors for sale , 5660 10D 760KV with cooler, $100.00 shipped , 5670 4Y 1000KV with cooler $120.00 shipped , both motors $200.00 shipped lower 48/ low use on them both have 8 MM bullets
<<<<<<<<<<<<<<<<<<<<<<<<<<<<5670 STILL FOR SALE $100.00 SHIPPED LOWER 48>>>>>>>>>>>>>>>>

[nmnorth]

new prices , 5660 $100.00 and 5670 $120.00 , or both for $200.00 shipped lower 48

[nmnorth]

weekly bump

[Leeandre]

The 5660 is 12s and the 5670 10s ?

[nmnorth]

5660 10s or 12s and 5670 8s or 10s

[nmnorth]

new price 5660 $80 5670 $100 , good deal 2 good motors

[Leeandre]

If you still have the 5660 I will take it shpiied to FL

[nmnorth]

yes i have the 5660 it , sending you PM

[Leeandre]

Payment sent.

[nmnorth]

5660 sold , 5670 still forsale , Bill

[maverick pro]

Will the 5670 push a 50inch apache?

[nmnorth]

it would on 9s or 10s , Bill

[Bp9145]

Will the 5670 push a 50inch apache?

Bill is correct on 9S or 10S. I have an Atomik ARC 58" cat using the same motor Bill has, TP 5670 4Y 1000kv with a FC 240A ESC and it ran in the low 50mph on 10S. On stock form I got it to run in the 44mph on 6S with a 120A esc after doing some tweaking. However, my ARC is not completely watertight as it has a top scoop which is covered with just a screen and at the back where I had two scoops, I modified that by removing the two scoops and putting louvers on them which furthermore provided another two areas where water could get in in case of a blowover. So I never had it on full throttle on 10S. So I imagine I could have pushed it to high 50mph or maybe hit 60mph? I since have removed the motor and plan to cover the scoops, the two louvers and make it watertight so I can make it a twin setup. But, yes the TP5670 is capable of pushing your 50" Apache and with a bigger and better ESC you can probably have it running in the 50- 60mph or maybe higher depending on the prop choice. Hope that helps your question.
Also, for $100 it's a good price.

[maverick pro]

The apache with hardware and rudder servo is 10lbs no motor esc or batts.
looking for 45-50mph with good run times. its a heavy boat as it used to be gas so the layup is solid.
How many runs on that motor? Still have plenty of life left?
Thank guys for the info.

[Bp9145]

The apache with hardware and rudder servo is 10lbs no motor esc or batts.
looking for 45-50mph with good run times. its a heavy boat as it used to be gas so the layup is solid.
How many runs on that motor? Still have plenty of life left?
Thank guys for the info.

The Atomik ARC specs says it's 13lbs (with two 3S 11.1V 30C 7500mAh LiPO batteries). .it's a fiberglass hull but pretty light for it's size. So I would say it's pretty close on weight wise with the Apache. Also, I forgot to mention I used 4 X 5S 5000mah batts which I'm sure added significant weight. I'm pretty sure with the TP 5670 with at least 240A esc, since that's what I'm gauging it on, and the right prop you could easily get it to 45-50mph. There are guys here with far greater experience than me and perhaps they could chime in to get you on the 45-50mph speed..