Selling large qty of items for a good friend. These servos have never been used. Everything but original box included.
NEW/Unused `HITEC HS625-MG ' Servo, comes w/hardware kit!
Retail $29.95
Asking $19.50 Shipped CONUS
SPECS:
Dimensions 1.59" x 0.77"x 1.48" (40.6 x 19.8 x 37.8mm)
Product Weight 1.94oz. (55.2g)
0utput Shaft Style 24 tooth (C1) spline
Voltage Range 4.8V - 6.0V
No-Load Speed (4.8V) 0.18sec/60°
No-Load Speed (6.0V) 0.15sec/60°
Stall Torque (4.8V) 76.37 oz/in. (5.5kg.cm)
Stall Torque (6.0V) 94.43 oz/in. (6.8kg.cm)
Max PWM Signal Range (Standard) 553-2520μsec
Travel per µs (out of box) .100°/μsec
Max Travel (out of box) 197°
Pulse Amplitude 3-5V
Operating Temperature -20°C to +60°C
Current Drain - idle (4.8V) 8.8mA
Current Drain - idle (6.0V) 9.1mA
Current Drain - no-load (4.8V) 400mA
Current Drain - no-load (6V) 500mA
Continuous Rotation Modifiable Yes
Direction w/ Increasing PWM Signal Clockwise
Deadband Width 8µs
Motor Type 3 Pole Ferrite
Potentiometer Drive
Indirect Drive
Feedback Style
5KΩ Potentiometer
Output Shaft Support
Dual Ball Bearings
Gear Type
Straight Cut Spur
Gear Material
3 Metal Gears and 1 Resin Metal Gear
Wire Length 11.81" (300mm)
Wire Gauge 22AWG
NEW/Unused `HITEC HS425-BB ' Servo, comes w/hardware kit!
****SOLD*****
SPECS:
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wave
Operating Voltage: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C
Operating Speed (4.8V): 0.21sec/60° at no load
Operating Speed (6.0V): 0.16sec/60° at no load
Stall Torque (4.8V): 45.82 oz/in. (3.3kg.cm)
Stall Torque (6.0V): 56.93 oz/in. (4.1kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
Continuous Rotation Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Current Drain (4.8V): 8mA/idle and 150mA no load operating
Current Drain (6.0V): 8.8mA/idle and 180mA no load operating
Dead Band Width: 8usec
Motor Type: 3 Pole Ferrite
Potentiometer Drive: Indirect Drive
Bearing Type: Dual Ball Bearing
Gear Type: Nylon
Connector Wire Length: 11.81" (300mm)
Dimensions: See Schematics
Weight: 1.6oz (45.5g)
NEW/Unused `HITEC HS225-MG ' Servo, comes w/hardware kit!
****SOLD****
Specs:
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wave
Operating Voltage: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C
Operating Speed (4.8V): 0.14sec/60° at no load
Operating Speed (6.0V): 0.11sec/60° at no load
Stall Torque (4.8V): 54.15 oz/in. (3.9kg.cm)
Stall Torque (6.0V): 66.65 oz/in. (4.8kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
Continuous Rotation Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Current Drain (4.8V): 8mA/idle and 300mA no load operating
Current Drain (6.0V): 8.8mA/idle and 340mA no load operating
Dead Band Width: 8usec
Motor Type: 3 Pole Ferrite
Potentiometer Drive: Indirect Drive
Bearing Type: 1 Ball Bearing and 1 Oilite Bushing
Gear Type: 4 metal and 1 nylon
Connector Wire Length: 11.81" (300mm)
Dimensions: See Schematic
Weight: 1.10oz (31g)
NEW/Unused `HITEC HS225-BB ' Servo, comes w/hardware kit!
***SOLD****
SPECS:
Dimensions 1.27" x 0.66"x 1.22" (32.4 x 16.8 x 31mm)
Product Weight 0.95oz (27g)
Output Shaft Style 24 tooth (C1) spline
Voltage Range 4.8V - 6.0V
No-Load Speed (4.8V) 0.14sec/60°
No-Load Speed (6.0V) 0.11sec/60°
Stall Torque (4.8V) 54.15 oz/in. (3.9kg.cm)
Stall Torque (6.0V) 66.65 oz/in. (4.8kg.cm)
Max PWM Signal Range (Standard) 553-2520μsec
Travel per µs (out of box) .097°/μsec
Max Travel (out of box) 191°
Pulse Amplitude 3-5V
Operating Temperature -20°C to +60°C
Current Drain - idle (4.8V) 8mA
Current Drain - idle (6.0V) 8.8mA
Current Drain - no-load (4.8V) 300mA
Current Drain - no-load (6V) 340mA
Continuous Rotation Modifiable No
Direction w/ Increasing PWM Signal Clockwise
Deadband Width 8µs
Motor Type 3 Pole Ferrite
Potentiometer Drive Indirect Drive
Feedback Style 5KΩ Potentiometer
Output Shaft Support 1 Ball Bearing and 1 Oilite Bushing
Gear Type Straight Cut Spur
Gear Material Nylon
Wire Length 11.81" (300mm)
Wire Gauge 25AWG
Pay Pal Welcome
Respond to this post `I'll take...!'
NEW/Unused `HITEC HS625-MG ' Servo, comes w/hardware kit!
Retail $29.95
Asking $19.50 Shipped CONUS
SPECS:
Dimensions 1.59" x 0.77"x 1.48" (40.6 x 19.8 x 37.8mm)
Product Weight 1.94oz. (55.2g)
0utput Shaft Style 24 tooth (C1) spline
Voltage Range 4.8V - 6.0V
No-Load Speed (4.8V) 0.18sec/60°
No-Load Speed (6.0V) 0.15sec/60°
Stall Torque (4.8V) 76.37 oz/in. (5.5kg.cm)
Stall Torque (6.0V) 94.43 oz/in. (6.8kg.cm)
Max PWM Signal Range (Standard) 553-2520μsec
Travel per µs (out of box) .100°/μsec
Max Travel (out of box) 197°
Pulse Amplitude 3-5V
Operating Temperature -20°C to +60°C
Current Drain - idle (4.8V) 8.8mA
Current Drain - idle (6.0V) 9.1mA
Current Drain - no-load (4.8V) 400mA
Current Drain - no-load (6V) 500mA
Continuous Rotation Modifiable Yes
Direction w/ Increasing PWM Signal Clockwise
Deadband Width 8µs
Motor Type 3 Pole Ferrite
Potentiometer Drive
Indirect Drive
Feedback Style
5KΩ Potentiometer
Output Shaft Support
Dual Ball Bearings
Gear Type
Straight Cut Spur
Gear Material
3 Metal Gears and 1 Resin Metal Gear
Wire Length 11.81" (300mm)
Wire Gauge 22AWG
NEW/Unused `HITEC HS425-BB ' Servo, comes w/hardware kit!
****SOLD*****
SPECS:
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wave
Operating Voltage: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C
Operating Speed (4.8V): 0.21sec/60° at no load
Operating Speed (6.0V): 0.16sec/60° at no load
Stall Torque (4.8V): 45.82 oz/in. (3.3kg.cm)
Stall Torque (6.0V): 56.93 oz/in. (4.1kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
Continuous Rotation Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Current Drain (4.8V): 8mA/idle and 150mA no load operating
Current Drain (6.0V): 8.8mA/idle and 180mA no load operating
Dead Band Width: 8usec
Motor Type: 3 Pole Ferrite
Potentiometer Drive: Indirect Drive
Bearing Type: Dual Ball Bearing
Gear Type: Nylon
Connector Wire Length: 11.81" (300mm)
Dimensions: See Schematics
Weight: 1.6oz (45.5g)
NEW/Unused `HITEC HS225-MG ' Servo, comes w/hardware kit!
****SOLD****
Specs:
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wave
Operating Voltage: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C
Operating Speed (4.8V): 0.14sec/60° at no load
Operating Speed (6.0V): 0.11sec/60° at no load
Stall Torque (4.8V): 54.15 oz/in. (3.9kg.cm)
Stall Torque (6.0V): 66.65 oz/in. (4.8kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
Continuous Rotation Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Current Drain (4.8V): 8mA/idle and 300mA no load operating
Current Drain (6.0V): 8.8mA/idle and 340mA no load operating
Dead Band Width: 8usec
Motor Type: 3 Pole Ferrite
Potentiometer Drive: Indirect Drive
Bearing Type: 1 Ball Bearing and 1 Oilite Bushing
Gear Type: 4 metal and 1 nylon
Connector Wire Length: 11.81" (300mm)
Dimensions: See Schematic
Weight: 1.10oz (31g)
NEW/Unused `HITEC HS225-BB ' Servo, comes w/hardware kit!
***SOLD****
SPECS:
Dimensions 1.27" x 0.66"x 1.22" (32.4 x 16.8 x 31mm)
Product Weight 0.95oz (27g)
Output Shaft Style 24 tooth (C1) spline
Voltage Range 4.8V - 6.0V
No-Load Speed (4.8V) 0.14sec/60°
No-Load Speed (6.0V) 0.11sec/60°
Stall Torque (4.8V) 54.15 oz/in. (3.9kg.cm)
Stall Torque (6.0V) 66.65 oz/in. (4.8kg.cm)
Max PWM Signal Range (Standard) 553-2520μsec
Travel per µs (out of box) .097°/μsec
Max Travel (out of box) 191°
Pulse Amplitude 3-5V
Operating Temperature -20°C to +60°C
Current Drain - idle (4.8V) 8mA
Current Drain - idle (6.0V) 8.8mA
Current Drain - no-load (4.8V) 300mA
Current Drain - no-load (6V) 340mA
Continuous Rotation Modifiable No
Direction w/ Increasing PWM Signal Clockwise
Deadband Width 8µs
Motor Type 3 Pole Ferrite
Potentiometer Drive Indirect Drive
Feedback Style 5KΩ Potentiometer
Output Shaft Support 1 Ball Bearing and 1 Oilite Bushing
Gear Type Straight Cut Spur
Gear Material Nylon
Wire Length 11.81" (300mm)
Wire Gauge 25AWG
Pay Pal Welcome
Respond to this post `I'll take...!'
Comment