Looking to sell my 40" mono. Ran it in Q-mono and Q-Offshore at the NAts this year and I got 3rd place in both.
Comes with all hardware, speedmaster 1/4" stinger strut, HOR SSS motor mount, 56mm x 84mm HOR SSS 1200kv motor, HOR Aluminum switch mount for wired Rx switch included. A 5 cell 2200Mah Nihm Rx pack is included. Flex is 1/4" Hughey cable. It has a functional oiler I use in combination with grease in summer and I just used grease on cold days. Also comes with HK 1/5th scale servo.
Hull is a Promise hobby hull that was a Carbon Kevlar layup. I added extra carbon Kevlar inlay as it was pretty thin. There are some filled holes in the port side when I moved the water outlets and some voids in the layup have been filled but, not so pretty. The bottom of the hull was worked/ Blueprinted you could say so it runs very well. The battery tray is 4mm thick pure carbon fiber plate with battery straps. There is a second Aluminum switch mount on it I will leave or remove at your discretion. It was for the SF240 esc Not included.
Top hatch has been severely worked over in order to sit flat as from factory it was extremely warped and almost impossible to tape down. Is has stress cracks but, that had to happen in order for it to be flat so cowl locks could be used and the cowl has a pair of 1/8" thick tabs in front so the hatch will not come off. I still use tape to seal it. Cowl has around 3 extra layers of C/F or C/Kevlar added it's tough!
You will need a SF240 or similar, batteries and radio. I ran a pair of 5000Mah Dinogy 6S packs.
Boat runs well on a x648 for 4 minutes + in offshore with said above packs and for 6 lap races you can use a D/T x452 up to an X455.
ALL this for $250 OBO US funds by Paypal pick up only or we meet up 1/2 way. I'm in Milton Ontario.
Reason for selling: Too big and heavy for a guy in a wheelchair to handle anymore. I'll miss her now that she is running nice.
Comes with all hardware, speedmaster 1/4" stinger strut, HOR SSS motor mount, 56mm x 84mm HOR SSS 1200kv motor, HOR Aluminum switch mount for wired Rx switch included. A 5 cell 2200Mah Nihm Rx pack is included. Flex is 1/4" Hughey cable. It has a functional oiler I use in combination with grease in summer and I just used grease on cold days. Also comes with HK 1/5th scale servo.
Hull is a Promise hobby hull that was a Carbon Kevlar layup. I added extra carbon Kevlar inlay as it was pretty thin. There are some filled holes in the port side when I moved the water outlets and some voids in the layup have been filled but, not so pretty. The bottom of the hull was worked/ Blueprinted you could say so it runs very well. The battery tray is 4mm thick pure carbon fiber plate with battery straps. There is a second Aluminum switch mount on it I will leave or remove at your discretion. It was for the SF240 esc Not included.
Top hatch has been severely worked over in order to sit flat as from factory it was extremely warped and almost impossible to tape down. Is has stress cracks but, that had to happen in order for it to be flat so cowl locks could be used and the cowl has a pair of 1/8" thick tabs in front so the hatch will not come off. I still use tape to seal it. Cowl has around 3 extra layers of C/F or C/Kevlar added it's tough!
You will need a SF240 or similar, batteries and radio. I ran a pair of 5000Mah Dinogy 6S packs.
Boat runs well on a x648 for 4 minutes + in offshore with said above packs and for 6 lap races you can use a D/T x452 up to an X455.
ALL this for $250 OBO US funds by Paypal pick up only or we meet up 1/2 way. I'm in Milton Ontario.
Reason for selling: Too big and heavy for a guy in a wheelchair to handle anymore. I'll miss her now that she is running nice.
Nortavlag Bulc 
Comment