ALL SOLD for now until I build some more
C C ESC Hydra 200 Plus Amp’s
I WILL RELIST THESE IN OCT.
I have 3 ESC’s. For Sale
These are the same as the Hydra 240’s, without the extra wires on them.
If you look at the CC 120’s and the CC 240’s
They DO NO have Water cooling on the top set of Fet’s or the underside of the radio
board, These DO have the extra cooling on them.(Look at the first picture)
I use Copper plate and Copper tube to make the cooling plates, 4 Copper plates
on each ESC.
I also use silicone heat transfer compound between the Fet.s and the Copper
plates.
Copper is better and faster than Aluminum to draw heat away from the Fet’s
ESC’s come with
-- 4 extra Rubycon 35V – 470uf capacitors, 8 total
-- Turnigy UBEC 5A – set at 6Volt (to use the UBEC you must disconnect the red
wire on the radio plug) The reason that I use a UBEC is that the radio board
runs 10 to 20 degrees cooler when the internal BEC is not used.
-- Water tubing already installed
-- All 5.5mm gold plugs installed
-- Firmware V 1.04
-- Cutoff Voltage 12.4V for 4S
-- Motor timing 11 degrees
-- Start Power Normal
-- Current Limiter -Disabled
-- Throttle Curve – Linear
If you want me to change the programming, let me know.
These are the same ESC’s that I use in all my race boats.
I hold 2 race records in NAMBA with these ESC’s
You know the Amps in the turns is higher than at the ends of the straightaway’s
My average draw is over 140 Amp’s in race setup for both my P Mono and my P
Sport . My N2 boats (2S2P) draw over 150 Amp’s.
These ESC’s always come in under 100 degrees when racing.
$150.00 each shipped within the lower 48
If you want 2 extra plugs for 2P setups, let me know.
#1 and 3 are sold
#2 left- SOLD
Larry
C C ESC Hydra 200 Plus Amp’s
I WILL RELIST THESE IN OCT.
I have 3 ESC’s. For Sale
These are the same as the Hydra 240’s, without the extra wires on them.
If you look at the CC 120’s and the CC 240’s
They DO NO have Water cooling on the top set of Fet’s or the underside of the radio
board, These DO have the extra cooling on them.(Look at the first picture)
I use Copper plate and Copper tube to make the cooling plates, 4 Copper plates
on each ESC.
I also use silicone heat transfer compound between the Fet.s and the Copper
plates.
Copper is better and faster than Aluminum to draw heat away from the Fet’s
ESC’s come with
-- 4 extra Rubycon 35V – 470uf capacitors, 8 total
-- Turnigy UBEC 5A – set at 6Volt (to use the UBEC you must disconnect the red
wire on the radio plug) The reason that I use a UBEC is that the radio board
runs 10 to 20 degrees cooler when the internal BEC is not used.
-- Water tubing already installed
-- All 5.5mm gold plugs installed
-- Firmware V 1.04
-- Cutoff Voltage 12.4V for 4S
-- Motor timing 11 degrees
-- Start Power Normal
-- Current Limiter -Disabled
-- Throttle Curve – Linear
If you want me to change the programming, let me know.
These are the same ESC’s that I use in all my race boats.
I hold 2 race records in NAMBA with these ESC’s
You know the Amps in the turns is higher than at the ends of the straightaway’s
My average draw is over 140 Amp’s in race setup for both my P Mono and my P
Sport . My N2 boats (2S2P) draw over 150 Amp’s.
These ESC’s always come in under 100 degrees when racing.
$150.00 each shipped within the lower 48
If you want 2 extra plugs for 2P setups, let me know.
#1 and 3 are sold
#2 left- SOLD
Larry
Comment