FighterCat's October Garage Sale!

[FighterCat57]

if there are any water cooled motor mounts left, I would like to get 1.
If they are gone, are the 2 "L" 540 mounts still available? and if so I woul dlike them.
I can send a bankers check as we do not do the Pay Pal thing any more.
got burned on it a couple years cak.

thanks

carl cisneros

No Problem. Two 540 L mounts are left. I can hold them for you to send payment. Will PM address.

[FighterCat57]

Ben I just sent you 35 as a gift. Dont worry about shipping it till I fugure out if I want either (if still avail) the drives. If the shipping is more let me know. I just wanted to get you something b4 I left.

Gotcha covered. No worries.

[Boomer]

My buy list - if they are still available

Here are the items I would like to purchase.
12. Trim Tabs (1.5" x 1" approx) $7 for both
11. Hull/Hatch Screws $2.50 each (6 left)


I have a question on #7 item. Will these work/fit on EKOS using Flex shafts, Genesis, or Miss Geico.?I don't have a mic to measure the shafts, but think they are all 4mm
If they will I'll take um.

7. Two 5mm - 4mm Hex Couplers $8 each

Thank you
Boomer
Paypal "gift" works for me

[FighterCat57]

Here are the items I would like to purchase.
12. Trim Tabs (1.5" x 1" approx) $7 for both
11. Hull/Hatch Screws $2.50 each (6 left)


I have a question on #7 item. Will these work/fit on EKOS using Flex shafts, Genesis, or Miss Geico.?I don't have a mic to measure the shafts, but think they are all 4mm
If they will I'll take um.

7. Two 5mm - 4mm Hex Couplers $8 each

Thank you
Boomer
Paypal "gift" works for me

All 6 Hatch screws?

Genesis is 4mm, EKOS is 3mm and if the Miss G is .150, they will fit.

[Boomer]

I would like to purchase.
12. Trim Tabs (1.5" x 1" approx) $7 for both

I looked a little closer at your photo of the hatch screws, and will pass on those. I just found some push locks that will work better for my need.

(Couplings)The idea was to upgrade the EKOS and the Genesis. My MG is ok. So can't use um.

Man, you have to get up early to get the cool stuff. You can use my email address to bill me via palpay.
Thank you
Boomer

[FighterCat57]

I would like to purchase.
12. Trim Tabs (1.5" x 1" approx) $7 for both

I looked a little closer at your photo of the hatch screws, and will pass on those. I just found some push locks that will work better for my need.

(Couplings)The idea was to upgrade the EKOS and the Genesis. My MG is ok. So can't use um.

Man, you have to get up early to get the cool stuff. You can use my email address to bill me via palpay.
Thank you
Boomer

They fit the Genesis and the Miss G. Just not the EKOS.
Octura makes at 5mm - .130 that will work on the EKOS.

Hatch Screws are knurled head cap screws, Cowl Locks are push type twist locks with mechanical locking mechanisms.

I don't have your email address. PM sent.

[syncronized77]

Arghhhhhhhhhhh....i knew i shoulda called in sick today...then I probably wouldn't have missed this posting at work! Damn conference calls

[WrknItUp]

LOL Those that got stuff DOVE on it! I know i had too...

[MOSQUITO6717]

hello , do you still have 540 motor mount one left???

[FighterCat57]

hello , do you still have 540 motor mount one left???

Everything has been updated. OSE carries those mounts, http://www.offshoreelectrics.com/pro...prod=ose-80230.

[carlcisneros]

The payment went out in th email yesterday for the 2 540 motor mounts.

Carl

[FighterCat57]

The payment went out in th email yesterday for the 2 540 motor mounts.

Carl

Thanks!



Updated original post.

[FighterCat57]

Updated parts list.

[Team Jericho]

The hull looks sweet, can you give me more details on it? Is it laminate with white gel coat? Not sure if I would be confident enough yet to laminate in the engine mounts, fit rudder, and stingers properly though, and in the right locations for best performance...if you are good with that sort of work, would you consider an almost RTR package? :)

[FighterCat57]

The hull looks sweet, can you give me more details on it? Is it laminate with white gel coat? Not sure if I would be confident enough yet to laminate in the engine mounts, fit rudder, and stingers properly though, and in the right locations for best performance...if you are good with that sort of work, would you consider an almost RTR package? :)

Sure, I can do that. Although it's not that difficult to epoxy the parts in yourself. You don't have to mess with fiberglass, just epoxy the motor mounts in place and you'll be good to go. The rest is bolt on.

The hull is fiberglass and is sanded and ready for paint. It's brand new, right from the factory. Same factory that makes the Apparition Genesis and Osprey.