i bought this boat from sandy, in hopes of finishing it.. well my boat funds are running low and its right at the end... for one I jumped in alittle over my head with this boat, and i dont want to have all this cash and time tied up in a boat i dont know enough about and go burn it down due to lack of knowledge.. im in love with this boat and hate to see it go but, i think im going to stay under the 40" range from here on out. well anyways ill post up some pics and a list of everything the boat now has with it.
iv got alot more pictures if you want them feel free to pm me or email me
parts / accessories:
(2) demension engineering 12s lipo sheilds
(1) novak lipo cut off/ sheild for 2s lipo with blue LED low battery warning (for receiver)
20' of 1/8" orange cooling line
20' of 1/4" orange cooling line
(2) LEHNER 3080 9T motors w/ cooling jackets, billet collets and installed
(2) schulze 40.160 esc's (with 4 added caps from schulze on each esc)
(2) futaba hi-torque servos for scale rudder rigged and installed
10' of 8awg red battery cable
10' of 8awg black battery cable
10' of 10awg red battery cable
10' of 10awg black battery cable
20' of futaba servo wire
(20) futaba servo ends and connectors
(72) 8mm battery connectors (36male and 36female)
(5) futaba servo Y leads
(2) Turnigy 2s 5800mah lipo (receiver)
(1) castle BEC PRO
(8) velcro battery straps with metal d ring
(4) octura props, one set is counter rotating
billet hull mounted antenna with antenna tube
all the hardware and motors comes with S.S. allen screws
lots of carbon fiber, carbon fiber bulkheads with all the work done!
Hatch is fitted and latched, all flotation is installed.
high speed ceramic bearings on dirve shafts with s.s. stuff tubes.
cooling system installed from stainless.
scale drives all HPR (Hans Peter)
Only BVM adhesives used.
Only S.S. hardware used.
comes with a work stand (pvc with padding)
comes with HPR carbon fiber radio box
also comes with 2 full tubs of grimracer marine grease
i bought this boat with all the hard stuff done all the fab work was done by sandy, and i think that any boat builder would appreceate the time and effort he put into building this boat, with no mistakes and solid as a rock!!
serious offers only please. m trying to sell as a whole boat for now if it doesnt sell then i may part it out after?? not sure though iv got alot of money tied up in this boat, and anyone that knows anything about them knows how much money it takes to build one... if you add up all the parts iv got seperate its well over $5,000 just in parts all are brand new besides the schulze i bought those used
as a matching pair, and the hull and hardware.. sandy has around $4,800 just in the hull and hardware... remember this boat has never seem water yet nor have the lenehers ever been used all is new! seal it up, mount the escs and battery hold downs and your ready to go i kept the custom box that sandy shipped it to me in very well protected!
iv got it posted on:
offshoreelectrics.com
rumrunnerracing.com
rcuniverse.com
ebay.com
you can contact me:
email- palletco@gmail.com
cell- 270 929 9179 call or text
ofse personal messages i dont usually get on the other sites
or reply to the thread
thanks for looking
Blake
iv got alot more pictures if you want them feel free to pm me or email me
parts / accessories:
(2) demension engineering 12s lipo sheilds
(1) novak lipo cut off/ sheild for 2s lipo with blue LED low battery warning (for receiver)
20' of 1/8" orange cooling line
20' of 1/4" orange cooling line
(2) LEHNER 3080 9T motors w/ cooling jackets, billet collets and installed
(2) schulze 40.160 esc's (with 4 added caps from schulze on each esc)
(2) futaba hi-torque servos for scale rudder rigged and installed
10' of 8awg red battery cable
10' of 8awg black battery cable
10' of 10awg red battery cable
10' of 10awg black battery cable
20' of futaba servo wire
(20) futaba servo ends and connectors
(72) 8mm battery connectors (36male and 36female)
(5) futaba servo Y leads
(2) Turnigy 2s 5800mah lipo (receiver)
(1) castle BEC PRO
(8) velcro battery straps with metal d ring
(4) octura props, one set is counter rotating
billet hull mounted antenna with antenna tube
all the hardware and motors comes with S.S. allen screws
lots of carbon fiber, carbon fiber bulkheads with all the work done!
Hatch is fitted and latched, all flotation is installed.
high speed ceramic bearings on dirve shafts with s.s. stuff tubes.
cooling system installed from stainless.
scale drives all HPR (Hans Peter)
Only BVM adhesives used.
Only S.S. hardware used.
comes with a work stand (pvc with padding)
comes with HPR carbon fiber radio box
also comes with 2 full tubs of grimracer marine grease
i bought this boat with all the hard stuff done all the fab work was done by sandy, and i think that any boat builder would appreceate the time and effort he put into building this boat, with no mistakes and solid as a rock!!
serious offers only please. m trying to sell as a whole boat for now if it doesnt sell then i may part it out after?? not sure though iv got alot of money tied up in this boat, and anyone that knows anything about them knows how much money it takes to build one... if you add up all the parts iv got seperate its well over $5,000 just in parts all are brand new besides the schulze i bought those used
as a matching pair, and the hull and hardware.. sandy has around $4,800 just in the hull and hardware... remember this boat has never seem water yet nor have the lenehers ever been used all is new! seal it up, mount the escs and battery hold downs and your ready to go i kept the custom box that sandy shipped it to me in very well protected!
iv got it posted on:
offshoreelectrics.com
rumrunnerracing.com
rcuniverse.com
ebay.com
you can contact me:
email- palletco@gmail.com
cell- 270 929 9179 call or text
ofse personal messages i dont usually get on the other sites
or reply to the thread
thanks for looking
Blake
(new motor in, and Back on the water!) 
Comment