Setups

[Brushless55]

No...I have not tried any strut adjustment...Are you talking about the angle of the blades relative to the Transom?

what is your strut angle?
if they do need some adjustment this could help get more speed

[OldSoldier99]

what is your strut angle?
if they do need some adjustment this could help get more speed

I'm running zero strut angle (neutral). Flat as a pancake.

But, I think my rudder angle is off from the stock setting because the rudder hit something in the water and got bent backwards. I could not get it back exactly straight up and down so I'm still running a little positive rudder angle.

For any other newbies like me, I'm getting my definitions of strut angle, and positive and negative, etc from the Aquacraft SuperVee tuning page:

http://www.aquacraftmodels.com/boats/aqub22-tuning.html

[Brushless55]

Thats what I've used to from my SV manual..
What about your COG ?

[NitroVal]

If you wanna break 50mph on GPS, just find a river with a strong current and run with the river.. Instant 10 mph gain for free..

[Brushless55]

If you wanna break 50mph on GPS, just find a river with a strong current and run with the river.. Instant 10 mph gain for free..

[OldSoldier99]

OK...I cleaned up the wiring and if all goes well, I'll take it by the lake tomorrow morning when I drop my son off at school (school is near the lake). I'll be sure to take the GPS and let you guys know what happened.

Almost made it.... 48.8MPH is the best I could get even after reducing the lengths of all the wiring to minimum. I'm using Traxxas connectors (the new ones...not the old Tamiya connectors that melt).

[Brushless55]

Almost made it.... 48.8MPH is the best I could get even after reducing the lengths of all the wiring to minimum. I'm using Traxxas connectors (the new ones...not the old Tamiya connectors that melt).

try it down hill! ahhhh

[OldSoldier99]

If you wanna break 50mph on GPS, just find a river with a strong current and run with the river.. Instant 10 mph gain for free..

[OldSoldier99]

Thats what I've used to from my SV manual..
What about your COG ?

I know COG stands for center of gravity, but I don't know how to answer the question. All the weight is in the batteries and the batteries sit in the stock battery tray so I'd say the COG is about 2/3 to 3/4ths of the way toward the stern.

I'm thinking a smaller/lighter set of batteries would reduce the weight...perhaps a pair of 4s 4000s. The 5000s are heavy. 4000 at 25C would be 100A...that would be plenty of power for a 60A speed controller.

[Brushless55]

getting less mass in their could help?

[RCprince]

ThunderPower have added some 45c lipos. some 4s 2650's would put out 119amps @ 295 grams

[OldSoldier99]

New batteries...quest for 50MPH on 4S

ThunderPower have added some 45c lipos. some 4s 2650's would put out 119amps @ 295 grams

I just sold one of my laptops and got some new lipo batteries (I had one but needed a second one to pair up with it). I got MaxAmps 4s 4000mAH 20C 365 grams (actually thought they were 40C...didn't read the fine print at first). If you've been following this thread you know I've been trying to break the 50MPH barrier on 4s batteries, but I've been stuck at 48.8 MPH using my Zippy Lipo 4s 5000mAH 25C 506 grams batteries.

In theory, the Zippys should be better because they have both a higher C rating and a higher capacity...but they also weigh 165 grams more times 2 for two batteries that's 330 grams more weight. I'll keep ya posted.

OldSoldier

[Brushless55]

Keep it going man!

[Jeff Wohlt]

Bring your strut up 1/16" at a time until she starts to really loosen up.

Make sure you grease your flex lightly and then run some 3-n-1 oil down it and slip it in. Same with shaft end.

Make sure that rudder is not slowing you down...if you want you can cut some off which is scrubbing some speed. Take the turn fin off as well and tape the holes up.

I would also consider one more step up in pitch on the prop if you can and make sure it is very sharp.

You certainly want to use some 600 paper WD and lightly sand the sponson bottoms to get them nice,smooth and leather feeling. Use a little water when sanding these lightly.

[OldSoldier99]

Jeff,
Thanks for all the tips! Unfortunately, when I went to try my new batteries, I found out my port sid ESC is not working. I get power to the receiver, the rudder works, and starboard ESC works. The ESC is supposed to beep 4 times for a 4s battery. The starboard side ESC beeps, but the port side ESC does not.

On other parts of this forum, I think I saw that others have had problems with these stock ESCs. Guess I'll have to see if Venom support will send me another one.