Your MG that started off as a hull

[srislash]

Here are some project pics that Im currently working on.........

That's looking good Mardon.I like the "Cigarette"

Where are you guys???

And you know where I am http://forums.offshoreelectrics.com/...t-Komodo/page7

[tagasagwan]

Well, my day was almost perfect. Run my gasser a few times and it was fast. Then, with the strong winds and sloppy driving, boom! It collided with another fast boat. No damage to the other boat but, mine had a bent portside turn fin and sever damage to my tuned pipe and header. Oh well!

[srislash]

Well, my day was almost perfect. Run my gasser a few times and it was fast. Then, with the strong winds that and sloppy driving, boom! It collided with another fast boat. No damage to the other boat but, mine had a bent portside turn fin and sever damage to my tuned pipe and header. Oh well!

Atta boy,take it in stride..It is alll fixable and you'll get em back next week.

[HYDROJERRY]

That sucks Taga but everythings fixable except if your boats sitting at the bottum of the lake (Shawn)!!!!
Mardon lets see more pics of that Cigerette boat, im lovin it!!

[srislash]

That sucks Taga but everythings fixable except if your boats sitting at the bottum of the lake (Shawn)!!!!
Mardon lets see more pics of that Cigerette boat, im lovin it!!

Well I did get the gate key today so that I can get in to retrieve her.But,I came home with a Lazer 45 and a 47" DF

[tagasagwan]

The pipe was sent out for repairs but I have a new header and pipe coming in within the week so I'm good! lols!

Shawn- AC Lazer45? oooooh! are you going to the dark side???


Guys, Do you happen to have the parts listed below lying around collecting dust that you want to sell cheap???? It's for a 32" twin cat.


1.) Twin 3/16 Stingers set.
2.) Counter rotating props eg. X442's or X645's
3.) 2 X 4S lipos.
4.) Counter rotating driveline( Left & Right lay Flex cables,couplers 5mm-3/16)
5.) 2 x Seaking or Turnigy 120A esc's.

[macdon]

Well, my day was almost perfect. Run my gasser a few times and it was fast. Then, with the strong winds and sloppy driving, boom! It collided with another fast boat. No damage to the other boat but, mine had a bent portside turn fin and sever damage to my tuned pipe and header. Oh well!

Not too bad brader - minor ones and very repairable. You wanna know what happened to me...........

Just imagine this - you have a new gas boat and its a maiden run. You turn and loose total control with the boat running straight towards a concrete bank wall! Top that buddy! hahahaha!

[srislash]

I've got a pair of props for ya Stephan,I'll have to think about lipos,if you can keep them down to 6",R&L .150 cables but only cables.The shafts are cheap and I could order them on the next order.And glue them for you.

[srislash]

Not too bad brader - minor ones and very repairable. You wanna know what happened to me...........

Just imagine this - you have a new gas boat and its a maiden run. You turn and loose total control with the boat running straight towards a concrete bank wall! Top that buddy! hahahaha!

Oh no Please no bad maiden stories.

[tagasagwan]

I've got a pair of props for ya Stephan,I'll have to think about lipos,if you can keep them down to 6",R&L .150 cables but only cables.The shafts are cheap and I could order them on the next order.And glue them for you.

Nice! What size are the props? I'm looking at the Scott's 110mm stingers but it needs square end cables.

[tagasagwan]

Not too bad brader - minor ones and very repairable. You wanna know what happened to me...........

Just imagine this - you have a new gas boat and its a maiden run. You turn and loose total control with the boat running straight towards a concrete bank wall! Top that buddy! hahahaha!

mishap on maiden? Sounds very familiar!!! LOLS! At least you're boat doesn't have the big hole in it! Remember my Lazer's maiden? hahaha!

[srislash]

Nice! What size are the props? I'm looking at the Scott's 110mm stingers but it needs square end cables.

Nah,I would go with .150 cables and 3/16th shafts.The square ends are a pain.As far as props goes I have 43mm and 45mm I think.I'll have to decide which ones I don't want.I've only got the Twin G to run those on.

[tagasagwan]

Nah,I would go with .150 cables and 3/16th shafts.The square ends are a pain.As far as props goes I have 43mm and 45mm I think.I'll have to decide which ones I don't want.I've only got the Twin G to run those on.

I will be using the twin Feigao 10XL's 1668kv on 4S. So I guess those props are okay???

[srislash]

4s?Going safe are we?

[macdon]

Its so quiet in here! Anyone have maiden videos to share?

Ive been bummed since Sunday's mishap - so hope that I get to fix her up soon so I could look forward to my "cigarette" project!