Miss Geico 4s vs Spartan 6s

[Brushless55]

Could be any number of things...

The key is ARE YOU HAVING FUN!???

[bbosncali]

Having fun???? After one outing I'm addicted if it wasn't gonna snow this weekend id be out all day sat and Sunday. I know a lot of people suggest not to go 5s or 6s on my setup but I'm gonna try 5s. My question is do you think the x642 prop that I have is to big for 5s? I'm already living dangerously but I'm try to remove any weeknesses that I can and if that's to big than what would you suggest?

[Brushless55]

maybe something like a M440 could work out real nice

[wilsta67]

What prop are you running with that setup??

It's a octura x442 same diameter as stock prop but the pitch is differant I think

[bbosncali]

sorry for being a dumb ass but wat is the term saw and hot set up??
im running a cc1515 2200kv with a t-180 in a spartan and it runs great on 6s
im thinking of doing the same set up in my mg when it finally gets here but run it on 4s.
here is the vid of the s.h.i.t.b.o.x in action.
http://www.youtube.com/watch?v=8dTyfi8_agc

And unlike the leopard motor the cc is only rated at 14.8vlts

[Brushless55]

And unlike the leopard motor the cc is only rated at 14.8vlts

the CC1515 2200kv motor is rated to 27volts
same motor that comes in the Brushless ERevo and Brushless EMaxx

[bbosncali]

the CC1515 2200kv motor is rated to 27volts
same motor that comes in the Brushless ERevo and Brushless EMaxx

Your right my bad should have know better than to trust an ebay add... cc does say on there site that they can handle 6s didn't get exact voltage but its deffinetly rated above 4s

[Brushless55]

Your right my bad should have know better than to trust an ebay add... cc does say on there site that they can handle 6s didn't get exact voltage but its deffinetly rated above 4s

even the 1512 2650kv can take 6s
I have one of those I want to try in a rigger

[bbosncali]

even the 1512 2650kv can take 6s
I have one of those I want to try in a rigger

Yep both rated at 25.2 but the 1800kv only 16.8 go figure

http://www.castlecreations.com/products/neu-castle_motors.html

[Alexgar]

sorry for being a dumb ass but wat is the term saw and hot set up??
im running a cc1515 2200kv with a t-180 in a spartan and it runs great on 6s
im thinking of doing the same set up in my mg when it finally gets here but run it on 4s.
here is the vid of the s.h.i.t.b.o.x in action.
http://www.youtube.com/watch?v=8dTyfi8_agc

Might want to preorder some bearing from vxb.com I only get 15-20 runs on my cc2200 that I run 5 and 6s

[Alexgar]

Yep both rated at 25.2 but the 1800kv only 16.8 go figure

http://www.castlecreations.com/produ...le_motors.html

May only be rated to 4s but I didn't here that I had 2 runs on 5s in my bj26 on x442 and she really moved thinking about putting this in a ul1

[wilsta67]

Might want to preorder some bearing from vxb.com I only get 15-20 runs on my cc2200 that I run 5 and 6s

what do the bearings cost from there.
i can get a complete repair kit from castle for $25 consisting of
Motor Repair Kits

Each kit includes:

2 Bearings
Rotor / Magnet assembly
End Bell
Required spacers
Screws required to attach end-bell