Supervee rebuild

[BIGDG357]

oh, yeah sorry

[z400]

Autobailers and FE boats are not a good idea at all.


If you've got a leak, you need to fix that leak.
You want to eliminate any and all water inside the hull.
Whatever you do, do not resort to an Autobailer to fix your problems.

[BIGDG357]

I have no problem with water the but if one comes up my lipos will stand a chance until I notice the leak so it can be taken care of.Before the rebuild this boat stayed bone dry.

[Jackwgf]

Got any further on the rebuild yet??

[BIGDG357]

I have, the boat is finished I only need an esc I am thinking the himodel 200a. I have been really busy lately between remodeling going on in my house and work I dont have much time or money to put in to it but it will be happening real soon. I will get some pics up soon of the finished boat.

[Diesel6401]

That supervee looks awesome. You do great work. I'm interested into buying a supervee as my next boat. Are you changing the esc because the stock aquacraft escs are normally junk or did it fry in the crash. When you hit 56mph what setup where you using?

[BIGDG357]

This is my progress so far, I've gotten more bits and pieces together and I'll order the speed control tomorrow. Hopefully I can get it back in the water soon and I would like to see 60 mph out of it. We'll see.

[winner]

looks really good man! i like how everything is spread out among the hull it will make it alot easier to work on

[Jackwgf]

Done well dude, how did you go about polishing the harware?

[BIGDG357]

Done well dude, how did you go about polishing the harware?

The hardware actually was not that bad at all to polish.I started with 400 grit then 600 then finally 1000 .I did this at work for my lunch break I'd say a total of 2 hours.

[BIGDG357]

Finally got something going on here. The set up I will be running is a 10xl,Etti 150 running on 2x Zippy 5000mah 40c 3s.I actually got to run it today but by the time I was ready with the boat the sun was already going down so I didn't have time to tweak it any .It rode like crap I need to adjust the stinger the bow was bouncing really badly I could not get over half throttle but I did throw the gps in it and even with all of the hopping the gps showed 36 mph ,under half throttle, so I think I should get some pretty good speeds from this one as soon as the bouncing is calmed.

[watto]

Looks pretty awesome mate, I really need to start thinking about this sort of rebuild cause shes falling apart. So you guys polish the bastards hey? I spose it helps them slip through the drink better? My sv has damaged ribs,rear corners,cowl the nose has hit a limestone wall when the radio failed one time and the motor mount plate is bent. i bought a fiber glass repair kit but i've never done it before so do you's reckon from what i've said its fixable or should I just get a new hull?

[BIGDG357]

it sounds like minor fiberglass work , body filler and a little paint as far as the stringers those can be easily replaced whether you choose to go back with wood or carbon fiber like I did

[Diesel6401]

finally got something going on here. The set up i will be running is a 10xl,etti 150 running on 2x zippy 5000mah 40c 3s.i actually got to run it today but by the time i was ready with the boat the sun was already going down so i didn't have time to tweak it any .it rode like crap i need to adjust the stinger the bow was bouncing really badly i could not get over half throttle but i did throw the gps in it and even with all of the hopping the gps showed 36 mph ,under half throttle, so i think i should get some pretty good speeds from this one as soon as the bouncing is calmed.

amazing sv you have, appaluse on the carbon work and your attention to detail!!!

[watto]

Finally got something going on here. The set up I will be running is a 10xl,Etti 150 running on 2x Zippy 5000mah 40c 3s.I actually got to run it today but by the time I was ready with the boat the sun was already going down so I didn't have time to tweak it any .It rode like crap I need to adjust the stinger the bow was bouncing really badly I could not get over half throttle but I did throw the gps in it and even with all of the hopping the gps showed 36 mph ,under half throttle, so I think I should get some pretty good speeds from this one as soon as the bouncing is calmed.

yeh she looks lovely mate, got some serious cooling going on. just got a ? about that cf in the bottom of the hull how thick is it? lools like ist molded to the hull contures pretty good and how or what do you use exactly to fix everything? I've got no Idea when it comes to cf but think i need to start learning quick.