Feigao 540XL in UL-1 !

[Diesel6401]

Yeah, I'm also going to try to clear all programming on the CC...at least I'm getting some beeps and its not DOA.....Kills me to buy a $200 esc and see it get all freaked out over a little moisture.....When I was building them both this winter, I was kinda comparing which was the better esc...I have to say, the Etti150 w/caps bank in orange boat is still working fine, I just dont see the Fieago overtaking the Nue in speed...I miss my blue UL already..

I hope it all works out for you.

[Diesel6401]

great price on that esc, D!

Thanx buddddddddddddy. I'll let you know how it goes and if it's worth your time/money. Knowing HC & the Turnigy label i'm sure it is.

[Diesel6401]

Well I got the video up on youtube, not the best but runs but just testing. I just got my stock pile of batts from HC in today so I will try two 4s in parallel also I will try different battery postions and see what works best. Damn I NEED MY GPS ASAP... lol, I WANT SPEED CHECKS....

http://www.youtube.com/watch?v=ELmjwLeOzIk

[Brushless55]

Oh man!
looks fast...

[Colby]

Nice vid ... looks like it hauls ... any readings on the speed?

[wizard122]

Looks good Dale can't wait to run together soon

[wizard122]

You guys should get some spray lube with PTFE in it like Super lube water proofs most anything
http://www.super-lube.com/ I use it in my RX and servo works great

[Diesel6401]

Thanks for all the positive comments guys. Next I will try the 4s 3600mah 30c's in parallel and I will try 2s 4000mah 40c's in series. I really think the 4s is gonna be the winning ticket. I need the weight. I never had a blow over on my ul with the stock setup, since the new motor it's happened 3 times. I have a airdam standing by, but I hope the 4s is the fix for catching air. It was a blast running it.

[Diesel6401]

You guys should get some spray lube with PTFE in it like Super lube water proofs most anything
http://www.super-lube.com/ I use it in my RX and servo works great

I wonder if spray liquid electrical tape would work as well. I have some laying around in the shop.

[Diesel6401]

Nice vid ... looks like it hauls ... any readings on the speed?

Not yet, but I would guess like 150mph...

As soon as I get my new gps which I will order this week (tomorrow is pay day ), I will post some speeds for it and my sv with ul power.

[Brushless55]

I wonder if spray liquid electrical tape would work as well. I have some laying around in the shop.

I like that spray on my rx's
works great

[Diesel6401]

I like that spray on my rx's
works great

SWEEEEEET!!!! I'll put some on the my rx's this weekend then. Glad to know it works

[ncornacchi]

I must be interpertating something wrong....I wanted to buy the ABC 1518/3 blade, but it looks to me like the dia. is only 38.1 ( 1518-10-75(3) CLL 1.5 1.8 2.700 38.1 68.58 10 0.75 L 3 0.187 $29.95) The Grim is a 40mm ....I bought the M445 to get something to try until I can figure out the prop sizing mystery...

[ncornacchi]

I also think that the rudders that I had made may be contributing to the transom hop..I think the blunt end was causing too much lift....I had my buddy hone down the bottom edge to reduce resistance...see what happens this weekend..thanks for tip on contact cleaner guys, got the CC240 back to life last night!

[Brushless55]

yes, the blunt end will cause lift...