Want input from everyone for question

[grsboats]

I'm boating for more than 40 years and still learning about props.More than modifiyng props I would suggest to first learn how to properly sharp,profile,balance and heat threat a prop.Lot of records were set using stock props.What I use to do with my good props is save them via prop duplicators in case I need a repair or even duplicate that time consuming wheel.I still have my Hughey prop gauge that I use in combination to my Speedmaster just to compare numbers but this is part two of the lesson Like Mike well pointed out give a try to your handy skills working on a prop and check for some improvements.There are well known rules that can be applied to this task but I doubt there is a magical recipe for this topic.Gill

[1truckerdan]

http://www.propline.com/Propeller-General-Information/Propeller_Terminology.htm

[lenny]

Hey
Not sure if you already have this info,
But hear is some links.

http://www.fastelectrics.net/

http://forums.offshoreelectrics.com/...ions-somewhere.......
http://www.offshoreelectrics.com/propeller-chart.php

[raptor347]

More than modifiyng props I would suggest to first learn how to properly sharp,profile,balance and heat threat a prop.Lot of records were set using stock props.

Thank you Gill. That's the most important line in this thread. What passes for sharpened and balanced is generally pretty far from good.

The best exercise for learning props:
-Pick one model that you use regularly and buy 3 blanks.
-Prep all three to be identical in stock profile, run them to make sure.
-Modify one and test for performance. Repeat.

There's no replacement for getting your hands dirty.

P.S. WEAR YOUR SAFETY GEAR!!! BC isn't good for you.
-

[Cooper]

I'm boating for more than 40 years and still learning about props.More than modifiyng props I would suggest to first learn how to properly sharp,profile,balance and heat threat a prop.Lot of records were set using stock props.What I use to do with my good props is save them via prop duplicators in case I need a repair or even duplicate that time consuming wheel.I still have my Hughey prop gauge that I use in combination to my Speedmaster just to compare numbers but this is part two of the lesson Like Mike well pointed out give a try to your handy skills working on a prop and check for some improvements.There are well known rules that can be applied to this task but I doubt there is a magical recipe for this topic.Gill

Yup and lots of records are set with modified props too. I know not many are willing to cook their props at 600degrees for three hours, and actually duplicate the two blades profiles. That's kind of what I was talking about to potentially start a thread on. Proper modifications easy and hard. And what they are intended to accomplish and why. More of a hands on how to as a lot of info is out there but not much actual steps in the process. And also potentially learning some myself :). But just wanted to get an idea if it might upset some as prop work separates a lot of boats. And in my opinion all the knowledge and expertise of how to will not enable someone to craft the best shapes possible. I my eyes I agree that it is like an art form with function and not everyone can do it. But we can try :)

[Savage Skidoo]

search for SweetAccord's album in this fourm, it give you all kinds of info on prop lingo, mods such as detounging, cupping back cuts ect...

Right -on G-UNIT , I 2nd that , i goggled all there is on props . I have gotten many different tools to perform the task ahead and was able to put my own spin on them once better at the basic's , READ ...cause knowledge is know how . I'm not no 150 mph guy , but i have made some smooth running props ,i am very lucky to see my buds data logger and the prop mod's that i've done for him to see what works and what dose not . Man this can get expensive . One secret i do know they take time , leave the butchering to the meat cutters . CNC also need work don't be fooled . Mike

[BHChieftain]

Just a case in point on prop mods-- I bought a used M440 that was backcut and diameter reduced to 37mm and it is faster than a standard s/b x442...

Chief

[pond skipper]

On top of proper balancing, thinning, one of the other things that makes a big difference is knowing what props would be suitable for your setup, what the true capabilities of your setup is and what it's limits are, in a simple way to explain what I'm saying is that you wouldn't use cowboy boots to run a marathon, or wear sandals while attempting to climb Mount Everest, so first you will want to determine what your goals are, ill use my p mono as a bit of an example, I wanted a combination for it that would be fast, reliable, and safe. so for the 33" seaducer I picked the Neu 1521 1.5D, a castle hydra ice 240, 2x 2s 40c 7600 mah packs to keep the weight down but the discharge capabilities high enough to feed everything else, now to find a wheel for it, well like probably everyone else here I had to read and research props and figure out what works best for a setup like mine, well it being a mono obviously the best choice is going to be a prop with low lift characteristics that would have enough blade area to get the boat going and enough total pitch to get it to the speed I wanted it to reach, chose the octura X4 series because of the fact that its a very low lift prop, now I knew that on the Neu motors page they recommended an X447 3 blade but knowing I was going for speed more than bite I chose a 2 blade x450, a 2 blade is more efficient anyhow, so my next task was to figure out if there were any popular mods for X series props that would net any more speed from them and sure enough I found that if you detongue them it's like taking the restrictor plate off of them so to speak because you end up completely removing the low pitch area of the blade that's only used at super low speed which is not helpful at all when you just want to push the boat really fast. My goal was to get it over 60 and in taking my time and doing the best job I could just balancing, thinning, sharpening, and detonguing the prop without ever worrying about cupping, back cutting, or changing the rake angle to attempt to change the thrust cone any. And with starting from the absolute basics and getting everything as perfect as I can with the setup I have, I achieved 64.3 mph with what is basically a stock x series prop that had its blade shape changed to that of an m series prop...