Falcon 41 on 10s?

[Alexgar]

There is a swordfish 240 in the swap shop for 200$ fyi

[Brushless55]

I'd do a hydra ice hv so you had data logging if your buying new

we are going to do testing once we start building more boats, so an Eagle Tree is a tool we should get
but a Hydra would be a sweet direction

There is a swordfish 240 in the swap shop for 200$ fyi

[Alexgar]

check this out

http://fightercatracing.com/index.php?page=shop.product_details&flypage=flypage.tpl&product_id=87&category_id=10&option=com_virtuemart&Itemid=1

[Brushless55]

check this out
http://fightercatracing.com/index.ph...emart&Itemid=1

That would be awesome!
is 180amp enough?

[Alexgar]

not to famialiar with hv the highest i use is 6s what does the motor spec say?

[Alexgar]

im reading 110 amps that sound do able
5692 that is


Features:



- High efficiency up to 95%
- Powerful 4-pole design
- High overload ability



Specifications:



Model: LBP5692/3Y
Max Amps: 110A
Lipo Cell: 5-13s
Max Power: 5500W
KV(RPM/Volt): 730KV
Resistance: 0.0130
No-load Current(15V) : 1.7A
Diameter×Length (mm): Φ55.8×92
Mounting hole depth: 8mm
Length of extend Shaft : 20mm
Shaft Diameter (mm): Φ6.0
Weight: 880g

[Alexgar]

Specifications:



Model: LBP5682/3Y
Max Amps: 106A
Lipo Cell: 5-11s
Max Power: 4500W
KV(RPM/Volt): 910KV
Resistance: 0.0117
No-load Current(15V) : 2.1A
Diameter×Length (mm): Φ55.8×82
Mounting hole depth: 8mm
Length of extend Shaft : 20mm
Shaft Diameter (mm): Φ6.0
Weight: 758g

Model: LBP5682/3D
Max Amps: 180A
Lipo Cell: 4-6s
Max Power: 4500W
KV(RPM/Volt): 1670KV
Resistance: 0.0040
No-load Current(15V) : 5.5A
Diameter×Length (mm): Φ55.8×82
Mounting hole depth: 8mm
Length of extend Shaft : 20mm
Shaft Diameter (mm): Φ6.0
Weight: 758g

[Brushless55]

im reading 110 amps that sound do able
5692 that is

Specifications:

Model: LBP5692/3Y
Max Amps: 110A
Lipo Cell: 5-13s
Max Power: 5500W
KV(RPM/Volt): 730KV
Resistance: 0.0130
No-load Current(15V) : 1.7A
Diameter×Length (mm): Φ55.8×92
Mounting hole depth: 8mm
Length of extend Shaft : 20mm
Shaft Diameter (mm): Φ6.0
Weight: 880g

That's the 730kv
I'm still leaning towards the 1000kv and that one shows more amp draw

[Alexgar]

I found one over seas for 151

[Fluid]

No offense intended, but would it not be wise to listen to folks who have actually raced 10S boats over 40" long? There are a lot of them on this board, and spending the $$$ based on the opinions of folks with no experience is...risky. It's you money though...

I would not be too concerned about the amp rating of the Leopards. That rating is based on watts, not amps - pick the motor based on watts, and 5500 is better than 4500. It is common to exceed the manufacturer's amperage rating in boats. For example the Neu 2215 is rated for just 65 amps continuous, but we normally run 130-150 continuous amps through them. As long as they do not overheat they are fine. Use a big enough prop and you can load any of these motors to 250+ amps if you want - the motors won't like it though.


.

[Brushless55]

I found one over seas for 151

what did you find bro?
we are still leaning towards the 5692 1000kv
this could be somewhat like Tyler's Conquest Open Cat

[Brushless55]

we could also runs twins, but I think single would be more simple

[Alexgar]

i found the motor cheap but they want 50$ to ship ems only so its not that great of a deal

[Make-a-Wake]

For the 5692 on 10s you may consider an s240 or x457..............................

[Make-a-Wake]

Any progress................???