should i add caps to my t180?

[dreamland s4]

is it recommended to add caps to my seaking 180a esc? im installing this esc in my ul1 and running it on 6s with a tacon 1700kv and starting with a y536 then if temps dont bit*h me out ill up the prop to m440. should i add caps to the t180? if so, how do i do this?

[britscoot]

I use this and disconnected the internal bec
I have no problem running 6s.
http://www.offshoreelectrics.com/pro...035-lv&cat=136

[Alexgar]

i have one on my etti 150 they are super low profile perfect for tucking away and id say go for it they are easier to replace than the on board ones

[dreamland s4]

i have one on my etti 150 they are super low profile perfect for tucking away and id say go for it they are easier to replace than the on board ones

how do i install this? gotta link? or anything really.

[LiPo Power]

How old is it and what it says on the caps (specs)?

is it recommended to add caps to my seaking 180a esc? im installing this esc in my ul1 and running it on 6s with a tacon 1700kv and starting with a y536 then if temps dont bit*h me out ill up the prop to m440. should i add caps to the t180? if so, how do i do this?

[Alexgar]

ill get a pic tommorrow but ot has to contact points on the cap board and just solder to the underside of the batt input cables on the esc

[dreamland s4]

How old is it and what it says on the caps (specs)?

how old is what? my esc? never used. hasnt arrived yet.

[dreamland s4]

ill get a pic tommorrow but ot has to contact points on the cap board and just solder to the underside of the batt input cables on the esc

ohh 1 side of the contacts on the bottom of the board goes on the neg wire of esc, and the other on pos (respectively) correct? and this aids in doing what?

[LiPo Power]

how old is what? my esc? never used. hasnt arrived yet.

Obviously I am talking about your ESC and you never stated that you do not have it yet other than in your last respond #7.....

If your yet to come ESC will have 3 x 35V, 1000uF caps you shoud be save becouse these are the new caps they are installing on them.
If you still go ahead and decide to put more caps you can see what I did here ( other than Etti board ):
http://forums.offshoreelectrics.com/...ad.php?t=21512
Your welcome.....

[britscoot]

make sure to solder the etti board correctly.
Polarity is very important i found.
did mine wrong and it was like the 4th of july in my living room...lol

[LiPo Power]

that is right, plus goes with red and minus goes with black

make sure to solder the etti board correctly.
Polarity is very important i found.
did mine wrong and it was like the 4th of july in my living room...lol

[dreamland s4]

Obviously I am talking about your ESC and you never stated that you do not have it yet other than in your last respond #7.....

If your yet to come ESC will have 3 x 35V, 1000uF caps you shoud be save becouse these are the new caps they are installing on them.
If you still go ahead and decide to put more caps you can see what I did here ( other than Etti board ):
http://forums.offshoreelectrics.com/...ad.php?t=21512
Your welcome.....

i never knew there was a new version. and i thought maybe you were asking about the caps i have. sorry for the confusion. thanks for the link. awesome job!

[dreamland s4]

make sure to solder the etti board correctly.
Polarity is very important i found.
did mine wrong and it was like the 4th of july in my living room...lol

dang i guess u like yours well done! lol ill keep that in mind thanks!