MISS VEGAS FE w/UL-1 COWL???

[chummer]

OK hears the pics,

Curious... Where is the servo mounted?

[Shooter]

That would be quite a project! I think the cowl design on the pickle, the UL-1, and some of Randy's boats are the best. Simple, flat designs that tape easily.

What I'd really like is a slightly larger Vacupickle. That would be the bomb. Maybe I'll shoot Phil an email and see what he says!

[detox]

Phil has a new hull that looks alot like the Whiplash, but has that dreaded hump that needs taping. I hate humps.


...

[Shooter]

I'm with you there. Humps are for chumps. Are you talking about Phil Pace? Or that other boat that Propper just built? Or Phil Thomas?

[detox]

Phil Thomas. Look here:http://forums.offshoreelectrics.com/...ht=phil+thomas

[HYDROJERRY]

Curious... Where is the servo mounted?

The servo is in the left rear corner, if you guys want ill take pics tonight of inside the hull,,, the center cover has tabs on it so it hooks down nice and then some quick and easy taping, then the actual cowl has a bolt on the rear and anrubberband so super easy and fast....I was going to run the ul-1 motor and a Etti 150 i have but everyone says ill tear something up, just to much power i gess...

[chummer]

The servo is in the left rear corner, if you guys want ill take pics tonight of inside the hull,,, the center cover has tabs on it so it hooks down nice and then some quick and easy taping, then the actual cowl has a bolt on the rear and anrubberband so super easy and fast....I was going to run the ul-1 motor and a Etti 150 i have but everyone says ill tear something up, just to much power i gess...

Yes, I would like to see more pics.

That hull can take alot more power than the UL-1 motor can deliver. Although I think UL-1 motor might run a little hot in that hull, that's why I was curious how it ran. Maybe somebody with more knowledge can chime in here. I say run it and let us know how it goes.

[HYDROJERRY]

Some more pics,,,plus a saw a kb motor on the swap shop i may check it out for this hull..do you think it would be better, let me fine out what the kv is..

[Shooter]

Great photos Jerry. Can't understand why it would tear up the UL-1 motor?? As long as your propped correctly and watch temps when testing, I think it would be fine.

Thanks Detox. I've seen that Hull before. It's very nice, but that darn hump! It's a lot smaller than most though, so maybe it wouldn't be that bad.

[properchopper]

I guess I'm just one of those " Chumps with a Hump" , but then again, what do I know ?

http://www.youtube.com/watch?v=mJWAMNT-uLA

Maybe I should return the 2009 - 2010 NAMBA P-Sport Hydro 2-Lap record this boat holds

Seriously, taping the "hump" ain't no big deal

[Shooter]

Actually, I think the term would be "humperchumper" for you! ha ha!

Great vid. Always impressed with your stuff, especially that Vegas! You inspired me to get another one!

The hump on the new PT stealth hull is definitely smaller than most. I just remember those huge humps on the original UL boats from years back. Definitely a pain. You had to cross tape a certain way to get it to seal.

BTW guys, I'm actually considering putting a VP cowl on now. It's a little smaller, but boy does it make the boat look "slim and mean". Going with a NEU 1515 1Y and Hydra 240. I never used to run my gas vegas with the spoiler, but maybe I'll need it now?? Anyone have any clue?? I know Propper runs with a spoiler.

[chummer]

I guess I'm just one of those " Chumps with a Hump" , but then again, what do I know ?

http://www.youtube.com/watch?v=mJWAMNT-uLA

Maybe I should return the 2009 - 2010 NAMBA P-Sport Hydro 2-Lap record this boat holds

Seriously, taping the "hump" ain't no big deal

Propper,
You must be getting bored with that by now. Anychance of it hittin' the swap shop soon?

[Shooter]

Here is the VP cowl. Looks out of scale, but unique.

[Shooter]

Jerry - I'm curious. Since you have the option with your set-up, have you ever ran it without the cowl? Notice any handling/speed differences? Thanks.