Scott's ML GP335

[Brushless55]

Check this out - http://www.tppower.com/sort.asp?class_id=4&news=20

awesome, and thanks for the link
I have two of the 4060 motors (4092)
a 2100kv and 2600kv
2100kv in my PMono right now, and thought about trying the 2600kv in my P Sport Hydro

[jaike5]

Ray......... you know I have a P-hydro so does Jack, you gotta get out of bed before noon, and showing up at 1-1:30p. Racing stars at 10:00a most are there by 9:30a. Jay.

[ray schrauwen]

Been up since 6am. Boats are still ready from last year.

If we had a pond that could handle P-sport that would be nice too and it might get me out of bed earlier. London is looking to get shut down as I said it would years ago and Boxwood will never allow the full potential of P-sport but, that said I may bring it out for a spin this year if we can co-ordinate it. Last couple times I was there at 8:30 and John doesn't show until 10am so don't keep up that old drill it's worn out.

I've got my health together now too

Who is Jack? What P-sport does he have?

Ray......... you know I have a P-hydro so does Jack, you gotta get out of bed before noon, and showing up at 1-1:30p. Racing stars at 10:00a most are there by 9:30a. Jay.

[ray schrauwen]

Scorpion is make in-runners now too. So far only meant for the European guys but, they are boat specific. Just waiting to see what bigger motors they dream up:

SCORPION

awesome, and thanks for the link
I have two of the 4060 motors (4092)
a 2100kv and 2600kv
2100kv in my PMono right now, and thought about trying the 2600kv in my P Sport Hydro

[Richie the shipwright]

Really nice work Scott. Keep those photos coming!

[jaike5]

Been up since 6am. Boats are still ready from last year.

If we had a pond that could handle P-sport that would be nice too and it might get me out of bed earlier. London is looking to get shut down as I said it would years ago and Boxwood will never allow the full potential of P-sport but, that said I may bring it out for a spin this year if we can co-ordinate it. Last couple times I was there at 8:30 and John doesn't show until 10am so don't keep up that old drill it's worn out.

I've got my health together now too

Who is Jack? What P-sport does he have?

Ray glad your up early to bad everything is a cube , unless you want to run on L. Ont. which I'm in for, but most of all glad to hear your health is better. Jay.

[ray schrauwen]

Sorry to spam the thread, email me.

Ray glad your up early to bad everything is a cube , unless you want to run on L. Ont. which I'm in for, but most of all glad to hear your health is better. Jay.

[JohnZ]

TP motors look pretty good...don't know of any suppliers in the U.S. though.
How are they compared to the Leos?

[Richie the shipwright]

I hear tp are slightly pricier than leos but better... Also heard leos copied tp's designs....

rcboatbitz ship worldwide and are an agent for tp motors.

[Scott T]

So the cowl was really nicely moulded, but the scoop was a bit large for my liking. So I did some re-modelling!

I filled in parts of it with spray foam to give it support. I wasn't too fussed about the quality of the foam because it is all coming out later. Once the foam was set I marked the height I wanted the scoop and took to it with a hacksaw! I hope Mike's not offended....

I also sloped the front face of the scoop back. The foam will be shaped how I want it, then glassed over. Once done, the foam will be removed from the inside and a small amount of glass laid inside to tie it all together.

[Brushless55]

I dig it!

[Scott T]

Cowl is coming together now. I've done the glasswork and given it a rough fill&sand. Then I applied a coat of spray putty which shows up any pin holes and other imperfections. One side effect of angling the scoop back is that the cockpit becomes a bit longer. It's not perfect yet, but I'm liking the new look.

[Scott T]

Profile comparison with the cowl as supplied (ignore the vertical fins, I've decided against them).

[Brushless55]

Dig the new profile..

[JohnZ]

What's that 1/10 scale Crackerbox on the shelf underneath?